电瓶车电瓶修复方法分享

电瓶车电瓶修复方法分享(附图) 原理如图1，图2，将48V电瓶先加水，每格孔加6ml蒸馏水，（绝对不能加别的水）加好后放置一段时间，让蒸馏水浸润电瓶，然后串联一200W灯泡，接入220V市电，振荡一分钟，（不能长时间接入，一分钟够了），然后，将一800u/360V电容通过200W灯泡限流充电，等灯泡变暗后，断开市电，对电瓶放电，第一次放电很响，发出很亮的蓝白光，在充电，断开市电，对电瓶放电，连续7--10次，直到放电声小，火花也小时结束，用充电器正常充电，冲到转绿灯为止，就行了。对电瓶放电在图2中已交代，主要是先将220V市电通过200W灯泡限流，接一整流二级管（我用的是1N4007）这种管很好找的，主要注意正负极，不要搞错了，先对电容充电，灯泡的反应是先一亮，后慢慢变暗，等到灯泡暗下，看不到发光时电容这时已充满了，电容充好后断开市电，用4mm硬电线连接对电瓶放电。上图：如下 INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922222006afb87db0a379.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922222a5cb321900785dd.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922220a8d7f1ff3741d96.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922225bfe1780a5f4a258.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/110319222369a44bcf04dc284f.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922231b1e019a2833c5a4.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/1103192223a4978e519738c1a3.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922235efe6e18b7fc2b1c.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/11031922231c1636df3eb55d36.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/110319222345f194d6d2e519cb.jpg" \* MERGEFORMATINET INCLUDEPICTURE "http://www.jdwx.info/data/attachment/forum/month_1103/1103192224c1ade0e75083be92.jpg" \* MERGEFORMATINET