polo电脑调试(Polo computer debugging)
polo电脑调试(Polo computer debugging)
The factory Polo has a lot of functions are blocked, for example: the driver control alarm, brake wear alarm, 15km/h automatically locks, keys to unlock. To buy a VAS5053 USB data line, and then VAS5053 software (buy the line should be attached to) installed in your notebook, you can for your car, function switch, daily electrical module inspection, and so on.
----------------------------------------------------- commonly used function
---------------------------------------------------------
A, automatic locking, unlocking and flashing lights and horn set
1, enter 46 comfortable computer system
2, into 10 adjustments and matches
1) input channel
Channel 03 15km/h locks automatically (this is for my own experience, and some is 20)
Channel 04 pull out the key and unlock automatically
Channel 05, remote control, unlocking, warning, horn 2 sound; comfortable computer system should receive an alarm horn
Channel 06, remote control door lock, warning horn 1 sound; comfortable computer system to receive an alarm horn
(only the original pineapple / golf / Passat / Bora factory is imported and the alarm horn is installed by default)
Channel 07 remote control unlocks all turn on lights at 2 flashes
Channel 08 remote control door lock, turn all lights at the same time flash 1
2) enter the adjustment value 1 = open this function
0 = closes this function (new car factory defaults state is to close "0")
Two, single door and four door unlock unlock settings (default)
1, enter 46 comfortable computer system
2, enter 07 re coding
With 4 electric windows. Open 4 code at the same time is 00259; open only 1 code is 00258
With 2 electric windows. Open 4 code at the same time is 00067; open only 1 code is 00066
Uncharged window. Open 4 code at the same time is 00019; open only 1 code is 00018
Three, turn off the door, no keys, warning tone settings
1. Enter instrument panel 17
2, enter 07 re coding
1) to open the door to remind: the encoding is set to 00341 (original encoding 00141), light is not close open the door remains of former director of sound warning tone; lights off, the key didn't pull out, there will be a warning tone Dang Dang dang.
2) if you want to open the door to remind, and 125KM speeding reminder: the code is set to 00641
Four, the original remote control key matching
1, enter 46 comfortable computer system
2, enter 10 match adjustment
1) enter 01 in the channel number;
2) enter the number of remote control keys that match in the new value
3) save
4) each remote control press 2S.
Five, the original remote control key password matching
Record the additional information of the engine (14 bit) and the rack number (17 bits) with the data line, and go to the Volkswagen 4S to find the password for your car (7 digits)
Then begin:
1. Prepare all keys that need to be matched
2. Take out any switch and turn on the ignition
3, connect to the data line, open 5051B
4, enter 17 (combination instrument)
5, enter 11 (landing), next to the point of the 7 password, enter you go to ask the public service station code (4) and service provider code (3) and you ask the 7 digit anti-theft password
Enter the correct password after the point is executed or determined or OK
6, enter 10 (match adjustment)
7, after entering 10, the software default channel number is 00, change it to 21, and then click to read
8. Write the number of keys you need to match in the new value, and then save it
On the pop-up dialog box, the point is
9, then do not close the software, do not quit!! Pull out the key on the ignition switch
Insert second keys that need to be matched, switch on the ignition, and wait for 3 seconds to insert the third..
And so on. Until all key matching is complete!
Six, after cleaning throttle matching
1, enter 01 engines
2, enter 04 basic settings
1) in the group of type 060, according to GO!
2) until data shows OK.
Seven, query throttle status
1, enter 01 engines
2, enter 08 data monitoring
Number 03
Third Throt angle, that is, the throttle opening angle, note that the engine should be preheated (water temperature 90 degrees), otherwise the value is high, the value of more than 5 (normal range of value should be 1-5) on the wash
Eight, idle speed matching
1, enter 01 engines
2, enter 10 match adjustment
1) enter 01 in the channel number
2) enter 124-132 in the new value
3) save
The actual idle speed and range of adjustment depend on the specific conditions of the engine and the ECU. Low idle, easy to hold back, high waste oil
Nine, about the prompt function 00141
Enter [17 - meter device], select [7 - re coding], read the current encoding.
Factory settings 00143, different models should have different, we set the first ten million to pay attention to the original value of their car.
Encoding software combination instrument 17 control unit for 5 digit encoding, from left to right:
The first two (I'm now 02, try to set 07 or 06 and 03 to kill me)
History
+00 - no device available
+01 - brake friction, Chen piece wear instructions (brake pedal, cable sensor) alarm activation
+02 - seat belt alarm activated (on the speed dial, 6 seconds after power on, then out, as a reminder of the safety belt at ordinary times)
+04 - glass cleaning level alarm activation (basically useless, still alarm, not recommended)
Third (I set 6)
History
0 light warning + metric display 24 hours 11L/100KM
1 light warning + metric display 24 hours 11L/100KM
2 key reminder + light warning + English display 12 hours 11L/100KM
3 key reminder + light warning + metric display 12 hours 11L/100KM
4 light warning + English display 24 hours 11L/100KM
5 key reminder + metric display 24 hours 9.1KM/L (Polo not
supported, I have not tried)
6 speed reminder + key reminder + light warning + metric display 24 hours 11L/100KM
7 light warning + metric display 24 hours 11L/100KM
Fourth bit (I haven't changed factory settings: 4)
History
0: maintenance mileage unchanged and no oil / temperature sensor
1: maintenance mileage variable, and oil / oil / temperature sensor
2: maintenance mileage unchanged, and oil / oil / temperature sensor
3: car without maintenance display
The fifth bit (my PP is now 3, has been set at 1, and my heart works, feels great and changes again)
History
Mileage pulse code
Remarks:
Speed Alert: 125KM/H overspeed alarm;
Key reminder: after flameout did not pull the keys, open the cab door will open a warning; power did not shut the cab door, alarm, rub-a-dub
Light reminder: light does not close, drive the driver's door will alarm;
The metric system shows that the distance is kilometers, and the temperature is centigrade;
The British system shows mileage for miles and temperature for fahrenheit;
You can see the remaining gasoline in the tank by entering the 17 meter