为了正常的体验网站,请在浏览器设置里面开启Javascript功能!

三菱电梯故障代码

2017-09-26 11页 doc 36KB 53阅读

用户头像

is_435706

暂无简介

举报
三菱电梯故障代码三菱电梯故障代码 ————-E1 速度异常过低时检出《 SW-TGBL 》 ------E2 速度过大是检出《 SW-TGBH 》 ------E3 逆转是检出《 SW-TGBR 》 ------E4AST 异常时检出《 SW-AST 》 ------E5 逆变器过电流时检出《 SS-LOCFO 》 ------E6 整流器过电流检出《 SS-COVH 》 ------E7 整流器电压不足时检出《 SS-LVLT 》 ------E8LB 线圈故障断电时检出《 SW-CFLB 》 ------E95 线圈故障断电时检出《...
三菱电梯故障代码
三菱电梯故障代码 ————-E1 速度异常过低时检出《 SW-TGBL 》 ------E2 速度过大是检出《 SW-TGBH 》 ------E3 逆转是检出《 SW-TGBR 》 ------E4AST 异常时检出《 SW-AST 》 ------E5 逆变器过电流时检出《 SS-LOCFO 》 ------E6 整流器过电流检出《 SS-COVH 》 ------E7 整流器电压不足时检出《 SS-LVLT 》 ------E8LB 线圈故障断电时检出《 SW-CFLB 》 ------E95 线圈故障断电时检出《 SW-CFU 》 ------EA 迫力接点 ON/OFF 故障时检出《 SW-CFBK 》 ------EB 轿箱直接信号传输异常《 ST-STSCE 》 ------EC 厅外和指令直接信号传输异常《 ST-STSHE 》 ------ED 系统异常《 ST-SYER 》 ------EE 驱动在不能启动《 SD-DNRS 》 ------EF 控制在不能启动《 SW-NRS 》 维修的 -----E01 温度异常《 SW-THMFT 》 -----E02 紧急停止运行记录一次《 SW-EST1 》 -----E03CC-WDT3 次检出《 SS-SLCWC4 》 -----E04SLC-WDT4 次检出《 SS-SLCWC4 》 -------E05 过电流检出《 SW-SOCR 》 ------E06 再生电阻负载过大《 SW-SOLR 》 ------E0741DG 门锁电路异常《 SW-E41 》 ------E08 终端限位开关异常〈 SW — TSCK 〉 ------E09PAD 异常检出〈 SW-PAD 〉 ------E0A 称重数值异常检出〈 SW-WGER 〉 ------E0B 停止中 PAD 异常检出〈 SW-PAE 〉 ------E0C 充电异常〈 SW-CHRGD 〉 ------E0D 在平层时异常检出〈 SW-PRLE 〉 二(将 MON1 旋转到 1 位置,将 MON0 旋转到 1 位置时的显示结果如下: 显示结果: -----E10 没有异常 -----E11 复位后重试不能〈 SW-RSRTC 〉 -----E12 士力驼 16 次异常检出〈 ST-SELD 〉 -----E13 直接传输 CPU 传送异常〈 ST-STER 〉 -----E14 电容器异常检出〈 ST-CAPC 〉 -----E15 手动按钮异常〈 ST — HDOK 〉 ----E16 模式与测速数据偏差异常《 SD-OVJP 》 ----E17LB 线圈连续 4 次异常断电检出《 ST-DFLR 》 ----E185 线圈连续 4 次异常断电检出《 ST-DF5 》 ----E19 迫力连接回路连接 4 次异常检出《 ST-BFDK 》 ----E1A 整流器电压连续 8 次电压不足检出《 ST-DFLV 》 ----E1BRL 异常时检出《 ST-CFRL 》 ----E1CTSD 动作时异常检出《 SW-TSLDE 》 -----E1DESP 动作时异常检出《 SW-ESPE 》 三(将 MON1 旋转到 1 位置,将 MON0 旋转到 2 位置时的显示结果如下: 显示结果: ----E20 没有异常 ----E2189 回路异常检出《 SW-E89 》 ----E22 紧急停止运行记录 2 次《 SW-EST2 》 ----E23 系统异常《 ST-SYER 》 ----E24 回复后在尝试检出《 ST-RSRQH 》 ----E25 集极驱动板异常《 SS-GDFH 》 ----E26 DC-CT 异常《 SD-CTER 》 ----E27 油压迫力压力过低时检出《 SW-OPFER 》 ----E28 油压迫力油温,油量异常检出《 SW — OTLER 》 ----E29 温度异常《 SW-THMME 》 ----E2A 与最终速度偏差异常《 ST-UMCH 》 ----E2B 异常紧急停车后不能在启动《 SW — ETST 》 ----E2C 迫力异常动作 2 次《 SW-REBK2 》 ----E2D 整理器充电异常《 SW-VCHGT 》 ----E2E MELD 制板充电异常《 SD-MCHG 》 四(将 MON1 旋转到 1 位置,将 MON0 旋转到 3 位置时的显示结果如下: 显示结果: ----E30 没有异常 ----E31 MELD 负荷过大《 SD-SLTT 》 ————-E1 速度异常过低时检出《 SW-TGBL 》 ------E2 速度过大是检出《 SW-TGBH 》 ------E3 逆转是检出《 SW-TGBR 》 ------E4AST 异常时检出《 SW-AST 》 ------E5 逆变器过电流时检出《 SS-LOCFO 》 ------E6 整流器过电流检出《 SS-COVH 》 ------E7 整流器电压不足时检出《 SS-LVLT 》 ------E8LB 线圈故障断电时检出《 SW-CFLB 》 ------E95 线圈故障断电时检出《 SW-CFU 》 ------EA 迫力接点 ON/OFF 故障时检出《 SW-CFBK 》 ------EB 轿箱直接信号传输异常《 ST-STSCE 》 ------EC 厅外和指令直接信号传输异常《 ST-STSHE 》 ------ED 系统异常《 ST-SYER 》 ------EE 驱动在不能启动《 SD-DNRS 》 ------EF 控制在不能启动《 SW-NRS 》 维修的 -----E01 温度异常《 SW-THMFT 》 -----E02 紧急停止运行记录一次《 SW-EST1 》 -----E03CC-WDT3 次检出《 SS-SLCWC4 》 -----E04SLC-WDT4 次检出《 SS-SLCWC4 》 -------E05 过电流检出《 SW-SOCR 》 ------E06 再生电阻负载过大《 SW-SOLR 》 For example, to check the water and the presence of intestinal pathogenic bacteria of dairy products-eosin methylene blue medium is the identification of a common medium. Medium has a double function selection and identification. Such as macconkey medium commonly used in food testing is one example. It contains bile salts, lactose and neutral Red. Bile salts inhibit the intestinal bacteria other than ... In a small jar, with the media and sterilization to determine the final pH of the medium used. 8, sterile medium 121 c can be used for medium and high pressure steam sterilization method of 15 minutes. In a variety of preparation methods, in the absence of special provisions, you can use this method of sterilization. Some fear hot ingredients, such as sugar, separate into 20% or a more concentrated solution to filter or intermittent sterilization sterilization, again using aseptic technique and quantitative increases in media. Gelatin medium using low temperature sterilization. Blood, body fluids and antibiotics and the aseptic technique extraction and joined in after cooling of about 50 degrees Celsius in the medium. Agar slant medium should be taken out immediately after sterilization, cooling at the time 55 ?-60 ?, placed into proper falls to natural coagulation. 9, medium quality tests each batch of medium preparation done, should be carefully examined again, if cracks are found, water immersion, abnormal color, cotton was picked out by culture medium contamination, should be discarded. And determine the final pH. All media at 36 ? 1 ? constantprovides outside, should take without dry (or not to water, or not to solvent) of for try products for test, and will calculation in the of take dosage by check items Xia measuring have of dry weightlessness (or water, or solvent) deduction. 3. test in the of "blank test", Department refers to in not added for try products or to equivalent solvent alternative for try liquid of situation Xia, by with method operation proceeds of results; content determination in the of "and will titration of results with blank test correction", Department refers to by for try products by consumption titration liquid of volume (ML) and blank test in the by consumption titration liquid volume (ML) of poor for calculation. 4. test temperature, does not indicate the means at room temperature; temperature has significant influence on test results, except where otherwise provided, 25 ? ? 2 ? shall prevail. Four, testing water unless otherwise specified, refers to the purification of water. The pH check the water, means a new boiling water and cool to room temperature. Laboratory safety and protection in the fifth section, laboratory safety in the chemical laboratory, often are quite toxic, corrosive, flammable and explosive chemical direct contact often use of fragile glass and porcelain ware as well as in high temperature heating equipment such as gas, water, electricity ... Pour into glass bottle. 7. use oil-bath operation should be carefully heated, constantly measured with a thermometer, that the temperatures do not exceed oil temperature. 8. the residue of inflammable and easy explosive substance (such as sodium metal, white phosphorus, the match head) must not pour dirt bucket or sink should be collected within the specified container. 9. waste, especially in the strong acid and strong base cannot directly down to the tank should be ------E0741DG 门锁电路异常《 SW-E41 》 ------E08 终端限位开关异常〈 SW — TSCK 〉 ------E09PAD 异常检出〈 SW-PAD 〉 ------E0A 称重数值异常检出〈 SW-WGER 〉 ------E0B 停止中 PAD 异常检出〈 SW-PAE 〉 ------E0C 充电异常〈 SW-CHRGD 〉 ------E0D 在平层时异常检出〈 SW-PRLE 〉 二(将 MON1 旋转到 1 位置,将 MON0 旋转到 1 位置时的显示结果如下: 显示结果: -----E10 没有异常 -----E11 复位后重试不能〈 SW-RSRTC 〉 -----E12 士力驼 16 次异常检出〈 ST-SELD 〉 -----E13 直接传输 CPU 传送异常〈 ST-STER 〉 -----E14 电容器异常检出〈 ST-CAPC 〉 -----E15 手动按钮异常〈 ST — HDOK 〉 ----E16 模式与测速数据偏差异常《 SD-OVJP 》 ----E17LB 线圈连续 4 次异常断电检出《 ST-DFLR 》 ----E185 线圈连续 4 次异常断电检出《 ST-DF5 》 ----E19 迫力连接回路连接 4 次异常检出《 ST-BFDK 》 ----E1A 整流器电压连续 8 次电压不足检出《 ST-DFLV 》 ----E1BRL 异常时检出《 ST-CFRL 》 ----E1CTSD 动作时异常检出《 SW-TSLDE 》 -----E1DESP 动作时异常检出《 SW-ESPE 》 三(将 MON1 旋转到 1 位置,将 MON0 旋转到 2 位置时的显示结果如下: 显示结果: ----E20 没有异常 ----E2189 回路异常检出《 SW-E89 》 ----E22 紧急停止运行记录 2 次《 SW-EST2 》 ----E23 系统异常《 ST-SYER 》 ----E24 回复后在尝试检出《 ST-RSRQH 》 ----E25 集极驱动板异常《 SS-GDFH 》 ----E26 DC-CT 异常《 SD-CTER 》 ----E27 油压迫力压力过低时检出《 SW-OPFER 》 ----E28 油压迫力油温,油量异常检出《 SW — OTLER 》 ----E29 温度异常《 SW-THMME 》 ----E2A 与最终速度偏差异常《 ST-UMCH 》 ----E2B 异常紧急停车后不能在启动《 SW — ETST 》 ----E2C 迫力异常动作 2 次《 SW-REBK2 》 ----E2D 整理器充电异常《 SW-VCHGT 》 ----E2E MELD 制板充电异常《 SD-MCHG 》 四(将 MON1 旋转到 1 位置,将 MON0 旋转到 3 位置时的显示结果如下: 显示结果: ----E30 没有异常 ----E31 MELD 负荷过大《 SD-SLTT 》 ————-E1 速度异常过低时检出《 SW-TGBL 》 ------E2 速度过大是检出《 SW-TGBH 》 ------E3 逆转是检出《 SW-TGBR 》 ------E4AST 异常时检出《 SW-AST 》 ------E5 逆变器过电流时检出《 SS-LOCFO 》 ------E6 整流器过电流检出《 SS-COVH 》 ------E7 整流器电压不足时检出《 SS-LVLT 》 ------E8LB 线圈故障断电时检出《 SW-CFLB 》 ------E95 线圈故障断电时检出《 SW-CFU 》 ------EA 迫力接点 ON/OFF 故障时检出《 SW-CFBK 》 ------EB 轿箱直接信号传输异常《 ST-STSCE 》 ------EC 厅外和指令直接信号传输异常《 ST-STSHE 》 ------ED 系统异常《 ST-SYER 》 ------EE 驱动在不能启动《 SD-DNRS 》 ------EF 控制在不能启动《 SW-NRS 》 维修的 -----E01 温度异常《 SW-THMFT 》 -----E02 紧急停止运行记录一次《 SW-EST1 》 -----E03CC-WDT3 次检出《 SS-SLCWC4 》 -----E04SLC-WDT4 次检出《 SS-SLCWC4 》 -------E05 过电流检出《 SW-SOCR 》 ------E06 再生电阻负载过大《 SW-SOLR 》 ------E0741DG 门锁电路异常《 SW-E41 》 ------E08 终端限位开关异常〈 SW — TSCK 〉 ------E09PAD 异常检出〈 SW-PAD 〉 ------E0A 称重数值异常检出〈 SW-WGER 〉 ------E0B 停止中 PAD 异常检出〈 SW-PAE 〉 ------E0C 充电异常〈 SW-CHRGD 〉 ------E0D 在平层时异常检出〈 SW-PRLE 〉 二(将 MON1 旋转到 1 位置,将 MON0 旋转到 1 位置时的显示结果如下: 显示结果: -----E10 没有异常 -----E11 复位后重试不能〈 SW-RSRTC 〉 -----E12 士力驼 16 次异常检出〈 ST-SELD 〉 -----E13 直接传输 CPU 传送异常〈 ST-STER 〉 -----E14 电容器异常检出〈 ST-CAPC 〉 -----E15 手动按钮异常〈 ST — HDOK 〉 ----E16 模式与测速数据偏差异常《 SD-OVJP 》 ----E17LB 线圈连续 4 次异常断电检出《 ST-DFLR 》 ----E185 线圈连续 4 次异常断电检出《 ST-DF5 》 ----E19 迫力连接回路连接 4 次异常检出《 ST-BFDK 》 ----E1A 整流器电压连续 8 次电压不足检出《 ST-DFLV 》 ----E1BRL 异常时检出《 ST-CFRL 》 ----E1CTSD 动作时异常检出《 SW-TSLDE 》 -----E1DESP 动作时异常检出《 SW-ESPE 》 三(将 MON1 旋转到 1 位置,将 MON0 旋转到 2 位置时的显示结果如下: 显示结果: ----E20 没有异常 For example, to check the water and the presence of intestinal pathogenic bacteria of dairy products-eosin methylene blue medium is the identification of a common medium. Medium has a double function selection and identification. Such as macconkey medium commonly used in food testing is one example. It contains bile salts, lactose and neutral Red. Bile salts inhibit the intestinal bacteria other than ... In a small jar, with the media and sterilization to determine the final pH of the medium used. 8, sterile medium 121 c can be used for medium and high pressure steam sterilization method of 15 minutes. In a variety of preparation methods, in the absence of special provisions, you can use this method of sterilization. Some fear hot ingredients, such as sugar, separate into 20% or a more concentrated solution to filter or intermittent sterilization sterilization, again using aseptic technique and quantitative increases in media. Gelatin medium using low temperature sterilization. Blood, body fluids and antibiotics and the aseptic technique extraction and joined in after cooling of about 50 degrees Celsius in the medium. Agar slant medium should be taken out immediately after sterilization, cooling at the time 55 ?-60 ?, placed into proper falls to natural coagulation. 9, medium quality tests each batch of medium preparation done, should be carefully examined again, if cracks are found, water immersion, abnormal color, cotton was picked out by culture medium contamination, should be discarded. And determine the final pH. All media at 36 ? 1 ? constantprovides outside, should take without dry (or not to water, or not to solvent) of for try products for test, and will calculation in the of take dosage by check items Xia measuring have of dry weightlessness (or water, or solvent) deduction. 3. test in the of "blank test", Department refers to in not added for try products or to equivalent solvent alternative for try liquid of situation Xia, by with method operation proceeds of results; content determination in the of "and will titration of results with blank test correction", Department refers to by for try products by consumption titration liquid of volume (ML) and blank test in the by consumption titration liquid volume (ML) of poor for calculation. 4. test temperature, does not indicate the means at room temperature; temperature has significant influence on test results, except where otherwise provided, 25 ? ? 2 ? shall prevail. Four, testing water unless otherwise specified, refers to the purification of water. The pH check the water, means a new boiling water and cool to room temperature. Laboratory safety and protection in the fifth section, laboratory safety in the chemical laboratory, often are quite toxic, corrosive, flammable and explosive chemical direct contact often use of fragile glass and porcelain ware as well as in high temperature heating equipment such as gas, water, electricity ... Pour into glass bottle. 7. use oil-bath operation should be carefully heated, constantly measured with a thermometer, that the temperatures do not exceed oil temperature. 8. the residue of inflammable and easy explosive substance (such as sodium metal, white phosphorus, the match head) must not pour dirt bucket or sink should be collected within the specified container. 9. waste, especially in the strong acid and strong base cannot directly down to the tank should be ----E2189 回路异常检出《 SW-E89 》 ----E22 紧急停止运行记录 2 次《 SW-EST2 》 ----E23 系统异常《 ST-SYER 》 ----E24 回复后在尝试检出《 ST-RSRQH 》 ----E25 集极驱动板异常《 SS-GDFH 》 ----E26 DC-CT 异常《 SD-CTER 》 ----E27 油压迫力压力过低时检出《 SW-OPFER 》 ----E28 油压迫力油温,油量异常检出《 SW — OTLER 》 ----E29 温度异常《 SW-THMME 》 ----E2A 与最终速度偏差异常《 ST-UMCH 》 ----E2B 异常紧急停车后不能在启动《 SW — ETST 》 ----E2C 迫力异常动作 2 次《 SW-REBK2 》 ----E2D 整理器充电异常《 SW-VCHGT 》 ----E2E MELD 制板充电异常《 SD-MCHG 》 四(将 MON1 旋转到 1 位置,将 MON0 旋转到 3 位置时的显示结果如下: 显示结果: ----E30 没有异常 ----E31 MELD 负荷过大《 SD-SLTT 》
/
本文档为【三菱电梯故障代码】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。 本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。 网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。

历史搜索

    清空历史搜索