linux下判断哪个网卡连接

linux下判断哪个网卡连接 Linux系中判断哪个网卡是正在使用的统统统统统统统统统统统统统统 通统mii-tool指令 [root@localhost root]# mii-tool eth0: negotiated 100baseTx-FD, link ok eth1: no link 或 [root@localhost root]# mii-tool -v eth0: negotiated 100baseTx-FD, link ok product info: vendor 00:50:43, model 2 rev 3 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD eth1: no link product info: vendor 00:50:43, model 2 rev 3 basic mode: autonegotiation enabled basic status: no link capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control 或 [root@localhost root]# mii-tool -w 21:20:33 eth0: negotiated 100baseTx-FD, link ok 21:20:33 eth1: no link //mii-tool主要是用于配置网卡工作模式的指令,同也可以行、控等工作:统统统统统统统统统统统统统统统 2) [root@localhost /]# /etc/init.d/network status Configured devices: lo eth0 eth1 Currently active devices: lo eth0 等同于 [root@localhost root]# service --status-all ............ ............ Configured devices: lo eth0 eth1 Currently active devices: lo eth0 ............ ............ 3)ifconfig -a [root@localhost /]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:09:6B:09:08:FC inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::209:6bff:fe09:8fc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:106732953 errors:0 dropped:0 overruns:0 frame.:0 TX packets:104379788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:2351331877 (2.1 GiB) TX bytes:391707945 (373.5 MiB) Base address:0x2500 Memory:fbfe0000-fc000000 eth1 Link encap:Ethernet HWaddr 00:09:6B:09:08:FD BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame.:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Base address:0x2540 Memory:fbfc0000-fbfe0000 4)ethtool ethtool eth0 Settings for eth0: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: yes ethtool eth1 Settings for eth1: Supported ports: [ MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised auto-negotiation: Yes Speed: Unknown! (0) Duplex: Half Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) Link detected: no 从上面可以看出eth0 统统统统统统于接状,eth1没有接统统