［精选推荐］自动卧式插件机

［精选推荐］自动卧式插件机 XG-2000系列卧式插件机是用来将已经按程序编排好的42mm宽的卧式元件(如:电阻，二 极管等)和筒状跳线，按程序先后顺序自动地插入到PCB(电路板)的孔内，并折弯和剪 脚，将元件固定在PCB上。 该机器的一个显著特色是:可以直接将筒状跳线不经过再次编排而直接插入到PCB上，可 以节约1/3的跳线。在自行开发的软件配合下，该机器集三种功能于一身:既能单独插跳线， 又能单独插卧式电子元件，还能跳线和卧式元件混合插。一台机器，只需要一人操作，能完 成四十个人手动插件的产能。 三、机器的规格参数 1 理论速度 24000点/小时 2 插入不良率 小于200PPM 3 插入方向 平行0度,90度,180度,270度. 4 元件跨距 双孔距5.0mm-20mm(专插入跳线时可达到5mm-30mm) 5 基板尺寸 最小50mm*50mm、最大450mm*450mm 6 基板厚度 0.79-2.36mm 7 元件种类 电容器、晶体管、二极管、电阻、熔断丝等编带封装料。 8 跳线(JW) 独立输送方式.直径0.5mm-0.7mm镀锡铜线 9 元件引线剪脚长度 1.2-2.2mm(可调) 10 元件引线弯脚角度 10-35度(可调) 11 机器尺寸(长×宽×高) 1800mm×1600mm×1800mm 机器重量 700kg 使用电源 220V,AC(单相)50/60HZ,1.5KVA; 系统保护 不间断电源(UPS)配置，断电后可运行15分钟 使用功率 1.2KW(节能型) 使用气压 0.5Mpa 用气量 0.2立方/分钟 使用环境温度 5-25度 机器噪音 65分贝 孔位校正方式 机器视觉系统,多点MARK视觉校正. 驱动系统 AC伺服、AC马达 数据输入方式 USB接口输入(EXCEL文档格式), 控制系统 中文操作界面(WINDOWS系统控制平台)液晶显示器 工作台运转方式 顺时针和逆时针方向 线路板输送方式 手动/自动可选 XG-2000 Series horizontal machine is used to plug the program has been arranged by a good 42mm wide horizontal components (such as: resistors, diodes, etc.) and tube-like jumper, the order according to the procedure automatically inserted into the PCB (circuit board) of the hole, and bending and shear pin, the fixed component on the PCB. The machine is a notable feature: you can directly to the tube-like arrangement of jumper directly without re-inserted into the PCB, can save 1 / 3 of the jumper.Self-developed software in conjunction with the set of three functions in one machine: both single plug jumper, but also a separate electronic components inserted horizontal, and horizontal components can mix jumper plug.A machine, only one person, forty people to complete the manual plug-in capacity. Third, the machine specifications A theoretical speed of 24000 points / hour 2 into bad less than 200PPM 3 into the direction parallel to the 0 degrees, 90 degrees, 180 degrees, 270 degrees. 4 element double-pitch span 5.0mm-20mm (special insert jumper can reach 5mm-30mm) 5 substrate smallest 50mm * 50mm, maximum 450mm * 450mm 6 substrate thickness 0.79-2.36mm 7 types of capacitor components, transistors, diodes, resistors, fuse, etc. Tape packaging material. 8 jumper (JW) independent transportation methods. Tinned copper wire diameter 0.5mm-0.7mm 9 foot length of component lead cut 1.2-2.2mm (adjustable) 10 foot component lead bend angle 10-35 degrees (adjustable) 11 Dimension (L × W × H) 1800mm × 1600mm × 1800mm Weight 700kg Power supply 220V, AC (single phase) 50/60HZ, 1.5KVA; Uninterruptible Power System Protection (UPS) configured to run 15 minutes after power failure Use Power 1.2KW (energy type) Air pressure 0.5Mpa Gas Consumption 0.2 cubic meters / minute Ambient temperature 5-25 degrees Machine noise 65 db Hole correction method machine vision systems, multi-point MARK vision correction. AC servo drive systems, AC motors USB interface data input input (EXCEL Document Format), Chinese user interface control system (WINDOWS system control platform) liquid crystal display Table way clockwise and counterclockwise operation PCB transport mode Manual / Auto selectable