Photoshop如何将两张图片合并

Photoshop如何将两张图片合并 Photoshop如何将两张图片合并, 举例应用,有如下两张图, 图1 图2 appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width <1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row of neat, is reliable, the appearance is clean and not damaged. 7.5.8 cables neat and clean, solid binding, binding process in appearance. 7.5.9 the first cable production firm, crafts beautiful, clear signage does not fade. 7.5.10 fireproof plugging tight, no cracks and pores. 7.6 7.6.1 of the standard electrical wiring quality technology cable a, the multi-core wire bunch arrangement should be parallel to each other, horizontal wire harness or wire should be perpendicular to the longitudinal multi-core wire bunch. The distance between the wire harness and wire harness symmetry, and as close as possible. B-core wiring harness into round, multi-core wire bunch used g wire binding, fastening 要将图1和图2合并在一张图纸里,可以有如下方法, 2.设置图像大小, 首先设置图像的大小,只有设置了图像的大小,才好确定画布的大小,为接下来 的图片合并做准备,如图操作, appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width <1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row of neat, is reliable, the appearance is clean and not damaged. 7.5.8 cables neat and clean, solid binding, binding process in appearance. 7.5.9 the first cable production firm, crafts beautiful, clear signage does not fade. 7.5.10 fireproof plugging tight, no cracks and pores. 7.6 7.6.1 of the standard electrical wiring quality technology cable a, the multi-core wire bunch arrangement should be parallel to each other, horizontal wire harness or wire should be perpendicular to the longitudinal multi-core wire bunch. The distance between the wire harness and wire harness symmetry, and as close as possible. B-core wiring harness into round, multi-core wire bunch used g wire binding, fastening 2.设置画布大小, 设置画布的大小,宽和高一定要注意,一张图里要设置放下两张图的高度,纵向 方向的纸张，和宽度,横向方向的纸张，,另一张图里只设置一般的高度即可。 appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width <1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row of neat, is reliable, the appearance is clean and not damaged. 7.5.8 cables neat and clean, solid binding, binding process in appearance. 7.5.9 the first cable production firm, crafts beautiful, clear signage does not fade. 7.5.10 fireproof plugging tight, no cracks and pores. 7.6 7.6.1 of the standard electrical wiring quality technology cable a, the multi-core wire bunch arrangement should be parallel to each other, horizontal wire harness or wire should be perpendicular to the longitudinal multi-core wire bunch. The distance between the wire harness and wire harness symmetry, and as close as possible. B-core wiring harness into round, multi-core wire bunch used g wire binding, fastening 本例中,将图1设置成了放置两张图的大小,空白处放图2,图2 的设置图只需 要将图像大小设置好就行了,不需要再设置画布大小了。如下图, appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width <1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row of neat, is reliable, the appearance is clean and not damaged. 7.5.8 cables neat and clean, solid binding, binding process in appearance. 7.5.9 the first cable production firm, crafts beautiful, clear signage does not fade. 7.5.10 fireproof plugging tight, no cracks and pores. 7.6 7.6.1 of the standard electrical wiring quality technology cable a, the multi-core wire bunch arrangement should be parallel to each other, horizontal wire harness or wire should be perpendicular to the longitudinal multi-core wire bunch. The distance between the wire harness and wire harness symmetry, and as close as possible. B-core wiring harness into round, multi-core wire bunch used g wire binding, fastening 3.图片合并 首先将图2的窗口打开,如下操作, Ctrl+A,全选内容， Ctrl+C复制刚刚全选的内容。 打开图1的窗口,我们设置好的窗口，,如下操作, Ctrl+V粘贴刚刚复制的图2,在图1上随便点击哪里,就会出现图2的图片， 这时我们选择移动工具,然后再点选复制过来的图2,利用键盘的上下左右间将图片移到合适位置即可,如下图所示。 我们最好不要直接将图保存,最好是,否则改变了原图,等下次我们要用于其它地方的时候,不好编辑。 appearance of the weld appearance quality technical requirements of the project must not have a molten metal stream does not melt the base metal to weld, weld seam and heat-affected zone surface must not have cracks, pores, defects such as crater and ash, surface smoothing, weld and base metal should be evenly smooth transition. Width 2-3 mm from the edge of weld Groove. Surface reinforcement should be less than or equal to 1 + 0.2 times the slope edge width, and should not be greater than 4 mm. Depth of undercut should be less than or equal to 0.5 mm, total length of the welds on both sides undercut not exceed 10% of the weld length, and long continuous should not be greater than 100 mm. Wrong side should be less than or at 0.2T, and should not be greater than 2 mm (wall thickness mm t) incomplete or not allow 7.5 7.5.1 installation quality process standards of the electrical enclosure Cabinet surface is clean, neat, no significant phenomenon of convex, close to nature, close the door. 7.5.2 Cabinet Cabinet face paints no paint, returned to rusted, consistent color. 7.5.3 uniform indirect gap from top to bottom, slot width <1.5mm 7.5.4 adjacent Cabinet surface roughness is 0. 7.5.5 the cabinets firmly fixed, crafts beautiful. 7.5.6 Cabinet surface gauge, switch cabinet mark clear, neat, firm paste. 7.5.7 Terminal row of neat, is reliable, the appearance is clean and not damaged. 7.5.8 cables neat and clean, solid binding, binding process in appearance. 7.5.9 the first cable production firm, crafts beautiful, clear signage does not fade. 7.5.10 fireproof plugging tight, no cracks and pores. 7.6 7.6.1 of the standard electrical wiring quality technology cable a, the multi-core wire bunch arrangement should be parallel to each other, horizontal wire harness or wire should be perpendicular to the longitudinal multi-core wire bunch. The distance between the wire harness and wire harness symmetry, and as close as possible. B-core wiring harness into round, multi-core wire bunch used g wire binding, fastening