大众09G变速箱数据流

大众09G变速箱数据流 Is the 09G data stream useful? The 09G. J217 data group (28.74 KB)? ? ? Reading the measurement value block, Audi A3, 2004 > - automatic gearbox 09G shows the following measurements: display group 001:? Display area 1: engine speed (0 to 7650 RPM; failure: Error) display area 2: transmission input speed - G182 (0 to 7650 RPM) display area 3: the gearbox output speed - 195 (0 to 7650 RPM) display area 4: hang into gear (0: shift a P R: reverse N: gap 1 H, 1 M, 1 S: "1? 2 H, 2 M, 2 S, 3 H band 2, 3 M, 3 S, 3 4 H, 4 M, 4 S, 4 5 H, 5 M, 5 S, 5-speed 6 H, 6 M, S, H: 6 file open torque converter clutch M: torque converter clutch closed S: torque converter clutch slippage) display group 002: display area 1: transmission input speed - G182 (0 to 7650 RPM) display area 2: transmission input speed sensors - G182 voltage (0 to 5.15 V) display area 3: the gearbox output speed - G195 (0 to 7650 RPM) display area 4: the gearbox output speed sensor - G195 voltage (0 to 5.15 V) display group 003: display area 1: the current driver (failure: mistakes, DS, SO, WU, TT, AS, AC) display area 2: accelerate pedal value? (0 to 100%, has decreased by shift switch: force downshifts failure: Error) display area 3: vehicle speed (determined by the gearbox output speed sensor - G195) (0 to XXX km/h) :? Display area 4: hang into gear (0: hangs in park (P) R: reverse N: gap 1 H, 1 M, 1 S: "1? 2 H, 2 M, 2 S, 3 H band 2, 3 M, 3 S, 3 4 H, 4 M, 4 S, 4 5 H, 5 M, 5 S, 5-speed 6 H, M, 6 S: a six-speed H: torque converter clutch opened M: torque converter clutch closed S: torque converter clutch slip)? Display group 004: area 1: the shift lever position (P, R, N, D, S,? Manual/automatic shift slot: integrated manual failure: Error) display area 2: accelerate pedal value? (0 to 100%, has decreased by shift switch: force downshifts failure: Error) display area 3: to detect the state travel (Flat: UP: upgrade the ground DW: downhill Error: failure) display area 4: hang into gear (0: hangs in park (P) R: reverse N: gap 1 H, 1 M, 1 S: "1? 2 H, 2 M, 2 S, 3 H band 2, 3 M, 3 S, 3 4 H, 4 M, 4 S, 4 5 H, 5 M, 5 S, 5-speed 6 H, 6 M, S, H: 6 file open torque converter clutch M: torque converter clutch closed S: torque converter clutch slippage) display group 005: display area 1: empty display area 2: motion resistance index (0 to 100% : failure: the Error) display area 3: driving dynamic code (0 to 100%; failure: Error) display area 4: accelerator pedal value? (0 to 100%; has decreased by shift switch: force downshifts failure: Error) display block 006: display area 1: - G93 transmission oil temperature sensor (55 - to 205 ? C) display area 2:4 - N91, solenoid valve control current (0-1000 - A) display area 3: locking clutch state (0: locking clutch opened 1: locking clutch closed 2: locking clutch slippage) display area 4: locking clutch slippage? (1250 to 1250 RPM failure: Error) display block 007: display area 1:5 - N92, solenoid control current display area (0 to 2.550 A) 2:9 - N282 electromagnetic valve, control current display area (0 to 2.550 A) 3:3 - N90 electromagnetic valve, control current display area (0 to 2.550 A) 4:10 - N283, solenoid valve control current (0 to 2. Display group: 008, 550 A) display area 1: solenoid valve 6 - the N93, control current display area (0 to 2.550 A) 2:4 - N91 solenoid valve, control current display area (0 to 2.550 A) 3:2 - N89 - solenoid valve solenoid valve 1 - N88 state (00000000, 00000001: two electromagnetic valves are disconnected solenoid valve - N89 disconnect, solenoid valve - N88 on 00000010: solenoid valves - N89 connected, solenoid valve - N88 disconnect 00000011: two solenoid valves are connected) display area 4:15 (0 to xx V) terminal voltage display group 009: display area 1: brake test/brake light switch? (00000000: 制动测试和制动灯开关关闭 00000001: 制动测试开关打开，制动灯开关关闭(只有在出现故障时才可能发生) 00000010: 制动测试开关关闭，制动灯开关打开(只有在出现故障时才可能发生) 00000011: 制动测试和制动灯开关都打开) 显示区域2: 无油信息/降档开关 (00000000: 无油信息不可用且未按下降档开关 00000001: 无油信息不可用且已按下降档开关 00000010: 无油信息可用且未按下降档开关 00000011: 无油信息可用且按下了降档开关(正常情况下不可能发生)) 显示区域3: 换档杆位置 (P、R、N、D、S，? 手动/自动一体换档槽: 手动 出现故障时: Error) 显示区域4: 多功能开关-F125的设置 (P: 1001，? R: 1100，? N: 101，? D/手动/自动一体换档槽: 110，? S: 1111) 显示组010: 显示区域1: 变速箱机油温度传感器-G93 (-50至205 ?C) 显示区域2: 变速箱机油温度传感器-G93上的电压 (0至5 V) 显示区域3: 变速箱状态 (WL: 变速箱预热阶段，? 无读数: 正常状态下的变速箱， Error: 变速箱故障) 显示区域4: 端子电压 15 (0至xx V) 显示组011: 显示区域1: 制动灯开关电压 (Bls.ON: 制动灯开关打开，? Bls.OFF: 制动灯开关关闭) 显示区域2: 换档杆锁止电磁阀-N110 (SL: 电磁阀释放选档杆，电磁阀被激活，? --: 电磁阀锁止选档杆，电磁阀被屏蔽) 显示区域3: 车辆转速 (由变速箱输出转速传感器-G195决定) (0至xxx km/h)? 显示区域4: 换档杆位置 (P、R、N、D、S，? 手动/自动一体换档槽: 手动 出现故障时: Error) 显示组012: 显示区域1: 换档杆位置 (P、R、N、D、S，? 手动/自动一体换档槽: 手动 出现故障时: Error) 显示区域2: 手动电控换档程序开关-F189 (降档， 升档，? M-开关(手动/自动一体换档槽识别)， 无读数: 手动/自动一体式变速箱 显示区域3: 挂入的档位 (0: 挂入停车档(P位) R: 倒档 N: 空档 1H、1M、1S: 1档? 2H、2M、2S: 2档 3H、3M、3S: 3档 4H、4M、4S: 4档 5H、5M、5S: 5档 6H、6M、6S: 6档 H: 扭矩转换器离合器打开 M: 扭矩转换器离合器关闭 S: 扭矩转换器离合器 滑脱) 显示区域4: 力矩限制 (0至100%) 显示组013: 显示区 域1: 换档杆位置 (P、R、N、D、S， 手动/自动一体换档槽: 手 动， 出现故障时: Error) 显示区域2: 多功能开关-F125的设置 (P: 1001，? R: 1100，? N: 101，? D/手动/自动一体换档槽: 110，? S: 1111) 显示区域3: 手动电控换档程序开关-F189 (降 档， 升档，? M-开关(手动/自动一体换档槽识别)， No reading: manual/automatic one-piece gearbox) display area 4: manual control shift switch - F189 / manual control on the steering wheel - E389 shift program (xxxx1: manual control on the steering wheel - E389 shift switch - downshifts program; xxx1x: manual control on the steering wheel - E389 shift switch - shift up program; XX1XX? : manual control shift switch - F189 downshifts program; X1XXX: manual control switch - F189 shift procedure, identification; 1 XXXX: manual control shift program switch - F189 shift up) display group 014: display area 1: accelerator pedal value? (0 to 100%; has decreased by shift switch: force downshifts failure: Error) display area 2: empty display area 3: oil-free information (00000000: switch does not press, 00000001: the switch is pressed (accelerator pedal value of 0%)) display area 4: accelerator pedal values are not correct (00000000: switch does not press, 00000001: the switch is pressed) display group 015: display area 1: manual control shift programs on the steering wheel - E389 switch voltage (0 to 5 v) display area 2: empty display area 3: empty display area 4: empty display group 080: display area 1: changes to make code/date/manufacturers/manufacturers test status - manufacturers are numbered consecutively. (AN1 XXX/month. XXXX XXXX Hxx / 001) display group 125: display area 1: detection of engine control units (0: the engine in the engine control unit CAN engine 1: on the engine control unit) on CAN display area 2: the ABS control unit test (ABS 0: ABS control unit not on ABS 1: CAN the ABS control unit) on CAN display area 3: dashboard test (Combi 0: the dashboard is not on the CAN, Combi 1: the dashboard) on CAN display area 4: four-wheel drive control unit on the detection of (4 wd 0: four-wheel drive control unit is not on the CAN, 4 wd 1: four-wheel drive control unit in the CAN