贝尔7353与7342查看命令

简易概括： 1， 开通ONU 先注册----配置ELLID----配置管理INTERFACE------配置管理EOLTFLOW-------绑定管理IP 2, 配置宽带数据 OLT里面 先配置宽带端口INTERFACE------配置宽带端口EOLTFLOW--------绑定宽带端口IP ( 专线用户 ) 7353里面 配置网速模板------配置模板-------创建数据VLAN-------配置XDSL 用户端口------创建ATM PORT 的VCL ------创建ATM PORT 的Logical PORT ------- 创建 VLAN Bridge PORT --------创建 ATM PORT 与VLAN Bridge port 的 对应关系 3， 配置语音数据 OLT里面 先配置语音业务VLAN INTERFACE-------配置语音业务 EOLTFLOW -------绑定语音业务静态IP 7353 里面 创建语音VLAN----- 配置媒体网关数据（命令里包括语音IP，VLAN ，网关，软交换配置）-------配置端口语音数据 7353查看命令 RTRV-MEM::OSWP-1;查看版本 RTRV-IPPORT::NTENET::;查看管理ip RTRV-NE-ALL::COM::;查看管理网关 RTRV-MGNT::COM::;查看管理vlan 一： 宽带数据查看 RTRV-PROFILE-XSRVC::ALL;查看网速模版及使用情况 12:DU512-DN4M,LOCAL,ACTIVE,32:RAMODEDN=AT_INIT,RAMODEUP=AT_INIT" （12表示这个网速模板的名称或者代号，32表示已使用32次） RTRV-PROFILE-XBEARER::ALL;查看各网速模版的配置 "12::MINBRDN=256,MINBRUP=256,PBRDN=1024,PBRUP=512,MAXBRDN=4096,MAXBRUP=512,L2LPBRDN=128,MAXDELDN=6,MAXDELUP=6,MININPDN=0,MININPUP=0,ERASUREDETDOWNSTR=NOERASURE,ERASUREDETUPSTR=NOERASURE" 4096表示最大下行4M，512表示最大上行512K，,MAXDELDN=6,MAXDELUP=6交织度 RTRV-EQPT::ALL;(查看板卡状态) LT-1-1-1:MALT-A,MALT-A:LSMPWR=UP,BRDDES=:IS-NR(IS表示状态起来了，oos表示板卡未创或者板卡被拔出) LT-1-1-2:MPOT-A,MPOT-A:LSMPWR=UP,BRDDES=:IS-NR（MALT宽带板，MPOT语音板） RTRV-XDSL::XDSL-1-1-1-1:;查看1架1框1槽第一个端口状态 "XDSL-1-1-1-1::PORTID=available,XSRVCPROFID=12,XSRVCPROFNM=DU512-DN4M, XLNEPROFID=10,XLNEPROFNM=XDSL,XDPBOPROFID=0,OPMASKA=H'0000, OPMASKA2=H'00000000,OPMASKV=H'0000,OPMASKA2M=H'0000,OPMASKV2=H'0000, LCMODEA=H'0105,LCMODEA2=H'014C0004,LCMODEV=H'0000,LCMODEA2M=H'0004, LCMODEV2=H'0000,TPSTCMODE=DEFAULT,OVERRULE=NOTCREATED,INSMODE=DISABLE:IS-NR" IS表示有用户上网，猫已同步，DU512-DN4M, 表示最大上行512k和最大下行4m "XDSL-1-1-3-3::PORTID=available,XSRVCPROFID=12,XSRVCPROFNM=DU512-DN4M, XLNEPROFID=10,XLNEPROFNM=XDSL,XDPBOPROFID=0,OPMASKA=H'0000, OPMASKA2=H'00000000,OPMASKV=H'0000,OPMASKA2M=H'0000,OPMASKV2=H'0000, LCMODEA=H'0105,LCMODEA2=H'014C0004,LCMODEV=H'0000,LCMODEA2M=H'0004, LCMODEV2=H'0000,TPSTCMODE=DEFAULT,OVERRULE=NOTCREATED,INSMODE=DISABLE:OOS-AU" OOS表示无用户上网 "XDSL-1-1-3-3::PORTID=available,XSRVCPROFID=12,XSRVCPROFNM=DU512-DN4M, XLNEPROFID=10,XLNEPROFNM=XDSL,XDPBOPROFID=0,OPMASKA=H'0000, OPMASKA2=H'00000000,OPMASKV=H'0000,OPMASKA2M=H'0000,OPMASKV2=H'0000, LCMODEA=H'0105,LCMODEA2=H'014C0004,LCMODEV=H'0000,LCMODEA2M=H'0004, LCMODEV2=H'0000,TPSTCMODE=DEFAULT,OVERRULE=NOTCREATED,INSMODE=DISABLE:OOS-AUMA"OOS-AUMA端口关闭， 此时需执行ED-XDSL::XDSL-1-1-3-3::::PORTID=,XSRVCPROFID=12,XLNEPROFID=10:IS; XSRVCPROFID=12表示启用的是12这个网速模板 RTRV-XDSL::ALL 查看全部端口状态 关于用户无法上网，可以先查看用户端口状态，如果端口状态是IS，表明有用户在线。如果状态是OOS-AUMA，需执行ED-XDSL，放开端口 ···那一步，可以再查看端口的logport，如果logport也已经创建，再到OLT上查看，EOLTFLOW以及EVLANINTERFACE, ITV同理 RTRV-LOGPORT::ALL:;查看全部端口LOGPORT RTRV-LOGPORT::ATMPORT-1-1-1-1-8-35:;查看1架1框1槽第一个端口logport(宽带) RTRV-LOGPORT::ATMPORT-1-1-1-1-8-46:;查看1架1框1槽第一个端口logport(管理猫) RTRV-LOGPORT::ATMPORT-1-1-1-1-8-85:;查看1架1框1槽第一个端口logport(ITV) /* RTRV-LOGPORT::ALL: */ "ATMPORT-1-1-1-1-8-35:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=4,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0, DEFAULTSVLAN=0,DEFAULTCVLAN=461" "ATMPORT-1-1-1-1-8-85:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=2,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0, DEFAULTSVLAN=0,DEFAULTCVLAN=43" "ATMPORT-1-1-1-1-8-46:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=1,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0, DEFAULTSVLAN=0,DEFAULTCVLAN=45" "ATMPORT-1-1-1-2-8-35:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=4,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0,DEFAULTSVLAN=0,DEFAULTCVLAN=462" "ATMPORT-1-1-1-2-8-85:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=2,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0,DEFAULTSVLAN=0,DEFAULTCVLAN=43" "ATMPORT-1-1-1-2-8-46:::DEFPRIO=BESTEFFORT,MAXNUCMACADR=1,SELFLEARNSTA=UP,FRAMETYPE=ADMITONLYVLANUNTAGGED,QOSPROFILE=0,QOSPROFILENM=,PRIOREGPROF=0,DEFAULTSVLAN=0,DEFAULTCVLAN=45" 二 语音数据查看 RTRV-MEGACO-GW::MGW-1:;查看语音的管理IP与管理网关及软交换配置，主要看语音状态是否up "MGW-1:NAME=\"MGW134\",IPADDR=10.19.123.67,SUBNET=255.255.255.0,VLAN=201, PRIMMGCIPADDR=10.14.132.4,UDPPORT=2944,NXTHOP=10.19.123.1,PRIMMGCUDP=2944,SECMGCIP=10.14.132.100,SECMGCUDP=2944,MGCTYPE=HWSOFT3000,SIGNALDSCP=0,SIGPBIT=0,BEARDSCP=0,BEARPBIT=0,TERMIDTYPE=HIERARCHY,PSTNTERMFORMAT=\"AG170B/rack/shelf/slot/port\",MAXTRANSHANDLING=16000,MAXNETWORKDELAY=500,MAXRETRANS=7,REDBATDELAY=70000,RELEASEDELAY=30000,WTRLSDELAY=0,ACTHEARTBEAT=FIX-6500,PASSIVEHEARTBEAT=DYNAMIC,RETRANSMODE=FIX-1500,MAXWAITTIME=5,PROVRPLTIME=1000,EVTREQID=0,ALOFEVT=DISABLE,ALONEVT=DISABLE,ALOFSTRICTEVT=DISABLE,ALONSTRICTEVT=DISABLE,MGOVERLOADEVT=DISABLE,ACTIVEMGC=PRIMARY, ADMIN=UNLOCKED,STATUS=UP,IPMODE=MANUAL,DHCPOPTION60=\"\"" UNLOCKED端口已打开，状态UP，软交换与ONU已对接 RTRV-MEGACO-TM::ALL;查看所有语音端口状态 RTRV-MEGACO-TM::TM-1-1-1-1::;查看第一块语音板第一个端口语音状态 /* RTRV-MEGACO-TM::ALL */ "TM-1-1-1-1:TMID=1,MGWID=1,LINEFEED=25,IMPEDANCE=DEFAULT,BEARDSCP=\"3\, BEARPBIT=\"3\",ADMIN=UNLOCKED,STATUS=DOWN,DETAILSTATUS=REGISTERFAILURE" 端口是DOWN,未放号 "TM-1-1-1-2:TMID=2,MGWID=1,LINEFEED=25,IMPEDANCE=DEFAULT,BEARDSCP=\"3\,BEARPBIT=\"3\",ADMIN=UNLOCKED,STATUS=UP,DETAILSTATUS=IDLE" 端口UP,IDLE,表示已放号，正常 "TM-1-1-1-3:TMID=3,MGWID=1,LINEFEED=25,IMPEDANCE=DEFAULT,BEARDSCP=\"3\, BEARPBIT=\"3\",ADMIN=UNLOCKED,STATUS=UP,DETAILSTATUS=IDLE" "TM-1-1-2-64:TMID=128,MGWID=1,LINEFEED=25,IMPEDANCE=DEFAULT,BEARDSCP=\"3\",BEARPBIT=\"3\",ADMIN=UNLOCKED,STATUS=DOWN,DETAILSTATUS=REGISTERFAILURE" 以上是几条基本的查看语音命令 RTRV-L2FDB::ALL;学习用户的mac /* RTRV-L2FDB::ALL */ "ATMPORT-1-1-3-1-8-35:SVLAN=0,CVLAN=461:00E0D00048DC::SUBSVLAN=0, SUBCVLAN=461" "ATMPORT-1-1-3-4-8-35:SVLAN=0,CVLAN=464:00248CDFC894::SUBSVLAN=0, SUBCVLAN=464" 3槽第一端口学到的用户mac00E0D00048DC，业务vlan是461 RTRV-BOARDTEMP::ALL; 查看板卡温度 /* RTRV-BOARDTEMP::ALL */ "NTIO:1:ACTUAL_TEMPERATURE=28,TCATHRESHOLDLOW=75,TCATHRESHOLDHIGH=80, SHUTDOWNTHRESHOLDLOW=90,SHUTDOWNTHRESHOLDHIGH=95" "NT:1:ACTUAL_TEMPERATURE=34,TCATHRESHOLDLOW=75,TCATHRESHOLDHIGH=80,SHUTDOWNTHRESHOLDLOW=90,SHUTDOWNTHRESHOLDHIGH=95" "LT-1-1-1:1:ACTUAL_TEMPERATURE=35,TCATHRESHOLDLOW=100,TCATHRESHOLDHIGH=105,SHUTDOWNTHRESHOLDLOW=110,SHUTDOWNTHRESHOLDHIGH=115" "LT-1-1-2:1:ACTUAL_TEMPERATURE=36,TCATHRESHOLDLOW=100,TCATHRESHOLDHIGH=105,SHUTDOWNTHRESHOLDLOW=110,SHUTDOWNTHRESHOLDHIGH=115" NTIO板的温度是28度左右，NT主控板在34度左右，第一槽位板卡温度在35左右 7342查看命令 RTRV-ALM-ALL;查看所有告警及学到的onu的mac地址 "PON-1-1-2-1,PON:MN,NEWEONT,NSA,,,,: \"An unprovisioned ONT has been discovered on the PON,Mac=000772D7006C\""(表示在2槽第一个pon口学到新上报的onu 的mac) "LLID-1-1-3-1-11-0,LLID:CR,REPORTTIMEOUT,SA,,,,: \"Report Timeout Detecting\"" "LLID-1-1-3-1-10-0,LLID:CR,REPORTTIMEOUT,SA,,,,: \"Report Timeout Detecting\"" "LLID-1-1-3-1-1-0,LLID:CR,REPORTTIMEOUT,SA,,,,: \"Report Timeout Detecting\"" "ONT-1-1-3-1-11,ONT:MN,EDG,SA,,,,: \"Received Dying Gasp indication from ONT\"" "ONT-1-1-3-1-10,ONT:MN,EDG,SA,,,,: \"Received Dying Gasp indication from ONT\"" "ONT-1-1-3-1-1,ONT:MN,EDG,SA,,,,: \"Received Dying Gasp indication from ONT\""（既有LLID又有ONT告警的，onu设备掉电） RTRV-EPON::ALL;查看所有pon口状态 RTRV-EPON::PON-1-1-1-1::；查看第一个pon板第一pon口状态 /* RTRV-EPON::ALL */ "PON-1-1-1-1::EPONPOLLINGPERIOD=1000,EPONINTER0=15,EPONINTER1=30, EPONINTER2=60,EPONINTER3=60,EPONINTER4=60,EPONINTER5=60,EPONINTER6=60,EPONINTER7=60,AUTHMOD=MIX,,,,EPONDNBWPROFIDPERIOD=1:IS-NR" "PON-1-1-1-2::EPONPOLLINGPERIOD=1000,EPONINTER0=15,EPONINTER1=30, EPONINTER2=60,EPONINTER3=60,EPONINTER4=60,EPONINTER5=60,EPONINTER6=60, EPONINTER7=60,AUTHMOD=MIX,,,,EPONDNBWPROFIDPERIOD=1:IS-NR" "PON-1-1-1-3::EPONPOLLINGPERIOD=1000,EPONINTER0=15,EPONINTER1=30, EPONINTER2=60,EPONINTER3=60,EPONINTER4=60,EPONINTER5=60,EPONINTER6=60, EPONINTER7=60,AUTHMOD=MIX,,,,EPONDNBWPROFIDPERIOD=1:IS-NR" IS表示PON口状态正常，开局时一般OLTpon口全都打开了，OOS表示pon口未打开或未起来，如果原来状态是IS的，而现在状态是OOS，可能是下面pon口原来挂了onu，但是现在onu全部不工作（掉电等情况），pon口状态就可能是OOS RTRV-EONT::ALL;查看所有onu RTRV-EONT::ONT-1-1-1-1-1:;查看第一pon板第一pon口第一个onu "ONT-1-1-2-1-1::MACADDR=\"00-07-72-d7-01-df\",SWPLNDVER=\"UNPLANNED\", FECMODE=DISABLED,IGMPMODE=CONTROL,FASTLEAVE=DISABLED,MACAGING=71,DNRATELIMITMODE=NONE,PYSICALLNDADMIN=DISABLED,TEMPERATUREALMLOW=0,TEMPERATUREALMHIGH=17920,TEMPERATUREWARNLOW=0,TEMPERATUREWARNHIGH=17920,VOLTAGEALMLOW=31350,VOLTAGEALMHIGH=34650,VOLTAGEWARNLOW=31350,VOLTAGEWARNHIGH=34650,TXBIASALMLOW=2500,TXBIASALMHIGH=55000,TXBIASWARNLOW=2500,TXBIASWARNHIGH=55000,TXPWRALMLOW=7943, TXPWRALMHIGH=25110,TXPWRWARNLOW=25110,TXPWRWARNHIGH=7943,RXPWRALMLOW=40,RXPWRALMHIGH=5012,RXPWRWARNLOW=5012,RXPWRWARNHIGH=40,ONTVENDORID=\"ALU\",ONTMODELID=\"EMDU\",ONTHWVER=\"2527ABAB\",CHIPVENDORID=\"0203\",CHIPMODELID=\"3715\",CHIPVER=\"06071B\",BTRYBKUP=FALSE, SWVERACT=\"3FE52721AAAA03\",FMVER=\"3C18\",FECABILITY=SUPPORT,,RTT=3433, MAXSUPPORTLLID=1,ASSGNLLID=15360,ASSGNQUP=4,ASSGNQDW=1,MAXQLLID=20,MAXQPORT=20,MAXLLID=4,FENUM=7,GENUM=3,POTSNUM=0,E1NUM=0,ADSL2NUM=0,VDSLNUM=0,FEBITMAP=\"000000000014020F\",GEBITMAP=\"0000000006800000\": IS-NR"第二块板的第一pon口下的第一个onu状态是正常的 RTRV-ELLID::LLID-1-1-1-1-1-0::;查看第一pon板第一pon口第一个onu的llid RTRV-EVLANINTERFACE::VLANITF-1-1-1-1-1-0-101:;查看vlan的EVLANINTERFACE，(101管理vlan) RTRV-EVLANINTERFACE::VLANITF-1-1-1-1-1-0-301:;或者查看业务vlan301 的EVLANINTERFACE RTRV-EOLTFLOW::OLTFLOW-1-1-1-1-1-0-101-1:;查看vlan的EOLTFLOW(管理vlan101，同样查看业务vlan) RTRV-EOLTFLOW::OLTFLOW-1-1-1-1-1-0-301-1:; 用户无法上网，可以先在onu上查看数据，是否已经配置，上面已提到；然后在OLT上则先查看EOLTFLOW，如果没有EOLTFLOW,则再查看EVLANINTERFACE有没有，如果还没有则要补做该端口数据。 RTRV-PONARPENT::PONVLAN-3908;(3901外层)查看绑定的ONU ip（静态绑定的IP，包括管理IP、语音IP、专线用户IP等）和mac（ /* RTRV-PONARPENT::PONVLAN-3908 */ "PONVLAN-3908,EBRGPORT-1-1-1-8-1-0-101,218.2.62.69:00-07-72-d4-45-b1, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-2-0-101,218.2.62.70:00-07-72-d4-50-23, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-3-0-101,218.2.62.71:00-07-72-d7-3d-9c, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-4-0-101,218.2.62.72:00-07-72-d4-50-79, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-5-0-101,218.2.62.73:00-07-72-d4-50-a3, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-3-0-439,10.12.0.42:00-19-21-f1-91-66,STATIC: CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-4-0-201,10.19.123.39:00-07-72-e0-93-f5, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-1-0-201,10.19.123.37:00-07-72-d7-03-a8, STATIC:CVLAN=0" "PONVLAN-3908,EBRGPORT-1-1-1-8-2-0-201,10.19.123.38:00-07-72-e0-92-ee, STATIC:CVLAN=0" RTRV-PONFDBDYNAMIC::PONVLAN-3908:;查看学到用户的mac "PONVLAN-3908:00-0a-eb-bc-1a-27,EBRGPORT-1-1-1-8-3-0-455" "PONVLAN-3908:00-0b-b4-00-06-94,EBRGPORT-1-1-1-8-3-0-429" "PONVLAN-3908:00-0c-76-75-f5-7f,EBRGPORT-1-1-1-8-5-0-526" "PONVLAN-3908:00-10-5c-dd-2f-bd,EBRGPORT-1-1-1-8-3-0-433" "PONVLAN-3908:00-11-09-1b-e1-be,EBRGPORT-1-1-1-8-5-0-518" "PONVLAN-3908:00-11-5b-91-96-8b,EBRGPORT-1-1-1-8-3-0-386" "PONVLAN-3908:00-13-77-fd-4c-d3,EBRGPORT-1-1-1-8-5-0-581" "PONVLAN-3908:00-14-2a-99-64-0f,EBRGPORT-1-1-1-8-3-0-380" "PONVLAN-3908:00-14-2a-f2-97-67,EBRGPORT-1-1-1-8-5-0-551" "PONVLAN-3908:00-14-78-a2-52-f7,EBRGPORT-1-1-1-8-5-0-537" "PONVLAN-3908:00-15-58-a5-b0-bc,EBRGPORT-1-1-1-8-2-0-338" "PONVLAN-3908:00-16-17-42-55-90,EBRGPORT-1-1-1-8-3-0-402" "PONVLAN-3908:00-19-21-f1-91-66,EBRGPORT-1-1-1-8-3-0-439" 16160或者e420 在OLT上需多加一步业务设置（对端口打TAG） ENT-EONTENET::ONTENET-1-1-1-5-6-1-4::::AUTODETECT=ENABLED,VLANMODE= TAGGED,CVLANDEF=564,PBITDEF=0,MAXMACNUM=4,PMCOLLECTEDID=:IS; 第一槽位第5pon口第6个onu的第4端口，业务vlan是564 16160有16个端口，每个端口都要加这一步 E420个端口 RTRV-EONTENET::ONTENET-1-1-1-5-5-1-3:; EONTENET的查看命令 /* RTRV-EONTENET::ONTENET-1-1-1-5-5-1-3: */ "ONTENET-1-1-1-5-5-1-3::AUTODETECT=ENABLED,VLANMODE=TAGGED,CVLANDEF=367,PBITDEF=0,PAUSEADMIN=DISABLED,POLICYUPADMIN=DISABLED,UPCIR=1000000,UPBUCKET=2000,UPEXTBRSIZE=2000,POLICYDWADMIN=DISABLED,DWCIR=1000000,DWPIR=1000000,MULCFG=STRIP,MAXMACNUM=4,MAXMULGRP=16,PMCOLLECTEDID=DISABLED,AUTODETECTOPR=ENABLED, AUTONEGABILITY= 10baseT 10TFD 100T2 100T2FD 1000T 1000TFD:OOS-AU" 1槽5pon口第5个onu的第3端口，状态OOS，无用户