为了正常的体验网站,请在浏览器设置里面开启Javascript功能!

LMD18200中文资料

2014-01-09 13页 pdf 445KB 203阅读

用户头像

is_546427

暂无简介

举报
LMD18200中文资料 LMD18200 3A, 55V H-Bridge General Description The LMD18200 is a 3A H-Bridge designed for motion control applications. The device is built using a multi-technology pro- cess which combines bipolar and CMOS control circuitry with DMOS power devices on the same monoli...
LMD18200中文资料
LMD18200 3A, 55V H-Bridge General Description The LMD18200 is a 3A H-Bridge designed for motion control applications. The device is built using a multi-technology pro- cess which combines bipolar and CMOS control circuitry with DMOS power devices on the same monolithic structure. Ideal for driving DC and stepper motors; the LMD18200 ac- commodates peak output currents up to 6A. An innovative circuit which facilitates low-loss sensing of the output current has been implemented. Features n Delivers up to 3A continuous output n Operates at supply voltages up to 55V n Low RDS(ON) typically 0.3Ω per switch n TTL and CMOS compatible inputs n No “shoot-through” current n Thermal warning flag output at 145˚C n Thermal shutdown (outputs off) at 170˚C n Internal clamp diodes n Shorted load protection n Internal charge pump with external bootstrap capability Applications n DC and stepper motor drives n Position and velocity servomechanisms n Factory automation robots n Numerically controlled machinery n Computer printers and plotters Functional Diagram DS010568-1 FIGURE 1. Functional Block Diagram of LMD18200 December 1999 LM D18200 3A,55V H-Bridge © 1999 National Semiconductor Corporation DS010568 www.national.com 元器件交易网www.cecb2b.com Connection Diagrams and Ordering Information DS010568-2 11-Lead TO-220 Package Top View Order Number LMD18200T See NS Package TA11B DS010568-25 24-Lead Dual-in-Line Package Top View Order Number LMD18200-2D-QV 5962-9232501VXA LMD18200-2D/883 5962-9232501MXA See NS Package DA24B LM D1 82 00 www.national.com 2 元器件交易网www.cecb2b.com Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Total Supply Voltage (VS, Pin 6) 60V Voltage at Pins 3, 4, 5, 8 and 9 12V Voltage at Bootstrap Pins (Pins 1 and 11) VOUT +16V Peak Output Current (200 ms) 6A Continuous Output Current (Note 2) 3A Power Dissipation (Note 3) 25W Power Dissipation (TA = 25˚C, Free Air) 3W Junction Temperature, TJ(max) 150˚C ESD Susceptibility (Note 4) 1500V Storage Temperature, TSTG −40˚C to +150˚C Lead Temperature (Soldering, 10 sec.) 300˚C Operating Ratings(Note 1) Junction Temperature, TJ −40˚C to +125˚C VS Supply Voltage +12V to +55V Electrical Characteristics (Note 5) The following specifications apply for VS = 42V, unless otherwise specified. Boldface limits apply over the entire operating temperature range, −40˚C ≤ TJ ≤ +125˚C, all other limits are for TA = TJ = 25˚C. Symbol Parameter Conditions Typ Limit Units RDS(ON) Switch ON Resistance Output Current = 3A (Note 6) 0.33 0.4/0.6 Ω (max) RDS(ON) Switch ON Resistance Output Current = 6A (Note 6) 0.33 0.4/0.6 Ω (max) VCLAMP Clamp Diode Forward Drop Clamp Current = 3A (Note 6) 1.2 1.5 V (max) VIL Logic Low Input Voltage Pins 3, 4, 5 −0.1 V (min) 0.8 V (max) IIL Logic Low Input Current VIN = −0.1V, Pins = 3, 4, 5 −10 µA (max) VIH Logic High Input Voltage Pins 3, 4, 5 2 V (min) 12 V (max) IIH Logic High Input Current VIN = 12V, Pins = 3, 4, 5 10 µA (max) Current Sense Output IOUT = 1A (Note 8) 377 325/300 µA (min) 425/450 µA (max) Current Sense Linearity 1A ≤ IOUT ≤ 3A (Note 7) ±6 ±9 % Undervoltage Lockout Outputs turn OFF 9 V (min) 11 V (max) TJW Warning Flag Temperature Pin 9 ≤ 0.8V, IL = 2 mA 145 ˚C VF(ON) Flag Output Saturation Voltage TJ = TJW, IL = 2 mA 0.15 V IF(OFF) Flag Output Leakage VF = 12V 0.2 10 µA (max) TJSD Shutdown Temperature Outputs Turn OFF 170 ˚C IS Quiescent Supply Current All Logic Inputs Low 13 25 mA (max) tDon Output Turn-On Delay Time Sourcing Outputs, IOUT = 3A 300 ns Sinking Outputs, IOUT = 3A 300 ns ton Output Turn-On Switching Time Bootstrap Capacitor = 10 nF Sourcing Outputs, IOUT = 3A 100 ns Sinking Outputs, IOUT = 3A 80 ns tDoff Output Turn-Off Delay Times Sourcing Outputs, IOUT = 3A 200 ns Sinking Outputs, IOUT = 3A 200 ns toff Output Turn-Off Switching Times Bootstrap Capacitor = 10 nF Sourcing Outputs, IOUT = 3A 75 ns Sinking Outputs, IOUT = 3A 70 ns tpw Minimum Input Pulse Width Pins 3, 4 and 5 1 µs tcpr Charge Pump Rise Time No Bootstrap Capacitor 20 µs LM D18200 www.national.com3 元器件交易网www.cecb2b.com Electrical Characteristics Notes Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when op- erating the device beyond its rated operating conditions. Note 2: See Application Information for details regarding current limiting. Note 3: The maximum power dissipation must be derated at elevated temperatures and is a function of TJ(max), θJA, and TA. The maximum allowable power dis- sipation at any temperature is PD(max) = (TJ(max) − TA)/θJA, or the number given in the Absolute Ratings, whichever is lower. The typical thermal resistance from junc- tion to case (θJC) is 1.0˚C/W and from junction to ambient (θJA) is 30˚C/W. For guaranteed operation TJ(max) = 125˚C. Note 4: Human-body model, 100 pF discharged through a 1.5 kΩ resistor. Except Bootstrap pins (pins 1 and 11) which are protected to 1000V of ESD. Note 5: All limits are 100% production tested at 25˚C. Temperature extreme limits are guaranteed via correlation using accepted SQC (Statistical Quality Control) methods. All limits are used to calculate AOQL, (Average Outgoing Quality Level). Note 6: Output currents are pulsed (tW < 2 ms, Duty Cycle < 5%). Note 7: Regulation is calculated relative to the current sense output value with a 1A load. Note 8: Selections for tighter tolerance are available. Contact factory. Typical Performance Characteristics VSAT vs Flag Current DS010568-16 RDS(ON) vs Temperature DS010568-17 RDS(ON) vs Supply Voltage DS010568-18 Supply Current vs Supply Voltage DS010568-19 Supply Current vs Frequency (VS = 42V) DS010568-20 Supply Current vs Temperature (VS = 42V) DS010568-21 Current Sense Output vs Load Current DS010568-22 Current Sense Operating Region DS010568-23 LM D1 82 00 www.national.com 4 元器件交易网www.cecb2b.com Test Circuit Switching Time Definitions Pinout Description (See Connection Diagram) Pin 1, BOOTSTRAP 1 Input: Bootstrap capacitor pin for half H-bridge number 1. The recommended capacitor (10 nF) is connected between pins 1 and 2. Pin 2, OUTPUT 1: Half H-bridge number 1 output. Pin 3, DIRECTION Input: See Table 1. This input controls the direction of current flow between OUTPUT 1 and OUT- PUT 2 (pins 2 and 10) and, therefore, the direction of rotation of a motor load. Pin 4, BRAKE Input: See Table 1. This input is used to brake a motor by effectively shorting its terminals. When braking is desired, this input is taken to a logic high level and it is also necessary to apply logic high to PWM input, pin 5. The drivers that short the motor are determined by the logic level at the DIRECTION input (Pin 3): with Pin 3 logic high, both current sourcing output transistors are ON; with Pin 3 logic low, both current sinking output transistors are ON. All output transistors can be turned OFF by applying a logic high to Pin 4 and a logic low to PWM input Pin 5; in this case only a small bias current (approximately −1.5 mA) exists at each output pin. Pin 5, PWM Input: See Table 1. How this input (and DIREC- TION input, Pin 3) is used is determined by the format of the PWM Signal. DS010568-8 DS010568-9 LM D18200 www.national.com5 元器件交易网www.cecb2b.com Pinout Description (See Connection Diagram) (Continued) Pin 6, VS Power Supply Pin 7, GROUND Connection: This pin is the ground return, and is internally connected to the mounting tab. Pin 8, CURRENT SENSE Output: This pin provides the sourcing current sensing output signal, which is typically 377 µA/A. Pin 9, THERMAL FLAG Output: This pin provides the ther- mal warning flag output signal. Pin 9 becomes active-low at 145˚C (junction temperature). However the chip will not shut itself down until 170˚C is reached at the junction. Pin 10, OUTPUT 2: Half H-bridge number 2 output. Pin 11, BOOTSTRAP 2 Input: Bootstrap capacitor pin for Half H-bridge number 2. The recommended capacitor (10 nF) is connected between pins 10 and 11. TABLE 1. Logic Truth Table PWM Dir Brake Active Output Drivers H H L Source 1, Sink 2 H L L Sink 1, Source 2 L X L Source 1, Source 2 H H H Source 1, Source 2 H L H Sink 1, Sink 2 L X H NONE Application Information TYPES OF PWM SIGNALS The LMD18200 readily interfaces with different forms of PWM signals. Use of the part with two of the more popular forms of PWM is described in the following paragraphs. Simple, locked anti-phase PWM consists of a single, vari- able duty-cycle signal in which is encoded both direction and amplitude information (see Figure 2). A 50% duty-cycle PWM signal represents zero drive, since the net value of voltage (integrated over one period) delivered to the load is zero. For the LMD18200, the PWM signal drives the direc- tion input (pin 3) and the PWM input (pin 5) is tied to logic high. Sign/magnitude PWM consists of separate direction (sign) and amplitude (magnitude) signals (see Figure 3). The (ab- solute) magnitude signal is duty-cycle modulated, and the absence of a pulse signal (a continuous logic low level) rep- resents zero drive. Current delivered to the load is propor- tional to pulse width. For the LMD18200, the DIRECTION in- put (pin 3) is driven by the sign signal and the PWM input (pin 5) is driven by the magnitude signal. SIGNAL TRANSITION REQUIREMENTS To ensure proper internal logic performance, it is good prac- tice to avoid aligning the falling and rising edges of input sig- nals. A delay of at least 1 µsec should be incorporated be- tween transitions of the Direction, Brake, and/or PWM input signals. A conservative approach is be sure there is at least 500ns delay between the end of the first transition and the beginning of the second transition. See Figure 4. DS010568-4 FIGURE 2. Locked Anti-Phase PWM Control DS010568-5 FIGURE 3. Sign/Magnitude PWM Control LM D1 82 00 www.national.com 6 元器件交易网www.cecb2b.com Application Information (Continued) USING THE CURRENT SENSE OUTPUT The CURRENT SENSE output (pin 8) has a sensitivity of 377 µA per ampere of output current. For optimal accuracy and linearity of this signal, the value of voltage generating re- sistor between pin 8 and ground should be chosen to limit the maximum voltage developed at pin 8 to 5V, or less. The maximum voltage compliance is 12V. It should be noted that the recirculating currents (free wheel- ing currents) are ignored by the current sense circuitry. Therefore, only the currents in the upper sourcing outputs are sensed. USING THE THERMAL WARNING FLAG The THERMAL FLAG output (pin 9) is an open collector tran- sistor. This permits a wired OR connection of thermal warn- ing flag outputs from multiple LMD18200’s, and allows the user to set the logic high level of the output signal swing to match system requirements. This output typically drives the interrupt input of a system controller. The interrupt service routine would then be designed to take appropriate steps, such as reducing load currents or initiating an orderly system shutdown. The maximum voltage compliance on the flag pin is 12V. SUPPLY BYPASSING During switching transitions the levels of fast current changes experienced may cause troublesome voltage tran- sients across system stray inductance. It is normally necessary to bypass the supply rail with a high quality capacitor(s) connected as close as possible to the VS Power Supply (Pin 6) and GROUND (Pin 7). A 1 µF high-frequency ceramic capacitor is recommended. Care should be taken to limit the transients on the supply pin be- low the Absolute Maximum Rating of the device. When oper- ating the chip at supply voltages above 40V a voltage sup- pressor (transorb) such as P6KE62A is recommended from supply to ground. Typically the ceramic capacitor can be eliminated in the presence of the voltage suppressor. Note that when driving high load currents a greater amount of sup- ply bypass capacitance (in general at least 100 µF per Amp of load current) is required to absorb the recirculating cur- rents of the inductive loads. CURRENT LIMITING Current limiting protection circuitry has been incorporated into the design of the LMD18200. With any power device it is important to consider the effects of the substantial surge cur- rents through the device that may occur as a result of shorted loads. The protection circuitry monitors this increase in current (the threshold is set to approximately 10 Amps) and shuts off the power device as quickly as possible in the event of an overload condition. In a typical motor driving ap- plication the most common overload faults are caused by shorted motor windings and locked rotors. Under these con- ditions the inductance of the motor (as well as any series in- ductance in the VCC supply line) serves to reduce the mag- nitude of a current surge to a safe level for the LMD18200. Once the device is shut down, the control circuitry will peri- odically try to turn the power device back on. This feature al- lows the immediate return to normal operation in the event that the fault condition has been removed. While the fault re- mains however, the device will cycle in and out of thermal shutdown. This can create voltage transients on the VCC supply line and therefore proper supply bypassing tech- niques are required. The most severe condition for any power device is a direct, hard-wired (“screwdriver”) long term short from an output to ground. This condition can generate a surge of current through the power device on the order of 15 Amps and re- quire the die and package to dissipate up to 500 Watts of power for the short time required for the protection circuitry to shut off the power device. This energy can be destructive, particularly at higher operating voltages (>30V) so some precautions are in order. Proper heat sink design is essential and it is normally necessary to heat sink the VCC supply pin (pin 6) with 1 square inch of copper on the PCB. DS010568-24 FIGURE 4. Transitions in Brake, Direction, or PWM Must Be Separated By At Least 1 µsec LM D18200 www.national.com7 元器件交易网www.cecb2b.com Application Information (Continued) INTERNAL CHARGE PUMP AND USE OF BOOTSTRAP CAPACITORS To turn on the high-side (sourcing) DMOS power devices, the gate of each device must be driven approximately 8V more positive than the supply voltage. To achieve this an in- ternal charge pump is used to provide the gate drive voltage. As shown in Figure 5, an internal capacitor is alternately switched to ground and charged to about 14V, then switched to V supply thereby providing a gate drive voltage greater than V supply. This switching action is controlled by a con- tinuously running internal 300 kHz oscillator. The rise time of this drive voltage is typically 20 µs which is suitable for oper- ating frequencies up to 1 kHz. For higher switching frequencies, the LMD18200 provides for the use of external bootstrap capacitors. The bootstrap principle is in essence a second charge pump whereby a large value capacitor is used which has enough energy to quickly charge the parasitic gate input capacitance of the power device resulting in much faster rise times. The switch- ing action is accomplished by the power switches them- selves Figure 6. External 10 nF capacitors, connected from the outputs to the bootstrap pins of each high-side switch provide typically less than 100 ns rise times allowing switch- ing frequencies up to 500 kHz. INTERNAL PROTECTION DIODES A major consideration when switching current through induc- tive loads is protection of the switching power devices from the large voltage transients that occur. Each of the four switches in the LMD18200 have a built-in protection diode to clamp transient voltages exceeding the positive supply or ground to a safe diode voltage drop across the switch. The reverse recovery characteristics of these diodes, once the transient has subsided, is important. These diodes must come out of conduction quickly and the power switches must be able to conduct the additional reverse recovery current of the diodes. The reverse recovery time of the diodes protect- ing the sourcing power devices is typically only 70 ns with a reverse recovery current of 1A when tested with a full 6A of forward current through the diode. For the sinking devices the recovery time is typically 100 ns with 4A of reverse cur- rent under the same conditions. Typical Applications FIXED OFF-TIME CONTROL This circuit controls the current through the motor by apply- ing an average voltage equal to zero to the motor terminals for a fixed period of time, whenever the current through the motor exceeds the commanded current. This action causes the motor current to vary slightly about an externally con- trolled average level. The duration of the Off-period is ad- justed by the resistor and capacitor combination of the LM555. In this circuit the Sign/Magnitude mode of operation is implemented (see Types of PWM Signals). DS010568-6 FIGURE 5. Internal Charge Pump Circuitry DS010568-7 FIGURE 6. Bootstrap Circuitry LM D1 82 00 www.national.com 8 元器件交易网www.cecb2b.com Typical Applications (Continued) TORQUE REGULATION Locked Anti-Phase Control of a brushed DC motor. Current sense output of the LMD18200 provides load sensing. The LM3525A is a general purpose PWM controller. The relationship of peak motor current to adjustment voltage is shown in Figure 10. DS010568-10 FIGURE 7. Fixed Off-Time Control DS010568-11 FIGURE 8. Switching Waveforms LM D18200 www.national.com9 元器件交易网www.cecb2b.com Typical Applications (Continued) VELOCITY REGULATION Utilizes tachometer output from the motor to sense motor speed for a locked anti-phase control loop. The relationship of motor speed to the speed adjustment control voltage is shown in Figure 12. DS010568-12 FIGURE 9. Locked Anti-Phase Control Regulates Torque DS010568-13 FIGURE 10. Peak Motor Current vs Adjustment Voltage LM D1 82 00 www.national.com 10 元器件交易网www.cecb2b.com Typical Applications (Continued) DS010568-14 FIGURE 11. Regulate Velocity with Tachometer Feedback DS010568-15 FIGURE 12. Motor Speed vs Control Voltage LM D18200 www.national.com11 元器件交易网www.cecb2b.com Physical Dimensions inches (millimeters) unless otherwise noted 11-Lead TO-220 Power Package (T) Order Number LMD18200T NS Package Number TA11B LM D1 82 00 www.national.com 12 元器件交易网www.cecb2b.com Physical Dimensions inches (millimeters) unless otherwise noted (Continued) LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax:
/
本文档为【LMD18200中文资料】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。 本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。 网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。

历史搜索

    清空历史搜索