电脑每次启动都检测硬盘

电脑每次启动都检测硬盘 Every time the computer starts to self check, it's really not like, look at how I fix it. Method 1: Normally shutdown, after each restart, you must check the hard disk, and then after a variety of search, and finally find a solution: Click start to run, enter regedit in the run dialog box, open the registry editor, and select in turn "HKEY_LOCAL_MacHINE\SYSTEM\CurrentControlSet\Control\Session Manager" subkey, Then find the BootExecute key value in the right window and empty the value, and press the F5 key to refresh the registry. The reason may be that I've ordered the disk with voptxp! Study hard! Method 2: Select start to run, and type chkntfs /t:0 in the run dialog box to set the disk scan wait time to 0; if To ignore scanning a partition, such as when your computer C drive, can enter "chkntfs /x c:" command; if you want to restore the C Scan, you can use the "chkntfs /d c:" command, you can restore all chkntfs default settings, in addition to the automatic file check countdown . Other possibilities: 1, disable idle IDE channels Acceleration principle: because the Windows XP system automatically detects the IDE device on the computer during startup, it closes the idle IDE channel detection, thus accelerating system startup. However, for the spread of the wrong statement on the network, you need to correct it: a lot of people think that simply in Idle IDE channels are disabled in BIOS, and others recommend simultaneous shutdown in both BIOS and the system. First of all, the first method is... Not valid because the XP operating system can bypass the motherboard's BIOS and monitor the various states of the computer hardware independently; the latter looks like that again Carry coals to newcastle。 Therefore, only can be closed in the Windows XP system, in order to truly disable the idle IDE channel effect. Here's the following: right-click on my computer - properties, then click "hardware", and then click "device manager" to open in it" IDE ATA/PATA controllers (slightly different from different chips), then enter the main and minor IDE channels, and select advanced settings, in the Here, find the item "current transfer mode" is "not applicable" (this is what the idle IDE channel corresponds to), and the device type of this item Set it as "no", ok. 2, manually set the IP address Acceleration principle: Windows XP system is developed on the basis of Windows 2000, so it supports rich network functions. In it Windows XP will automatically detect whether the computer system connected to LAN in the boot, but general users are stand-alone Internet access in the network, and even Basically, all the settings are automatically IP addresses. Thus, the system searches for the DHCP server to assign a IP address to the machine However, the average user is not configured at all. This causes the system to take a long time to search the DHCP server until after it is turned on The IP address or service timeout will stop, even when you come to the desktop and double-click the program. That's a lot of use Windows XP users appear to enter the desktop after a "crash" 10 seconds problems, in fact, as long as the "local connection" manually assigned one A IP address can solve this problem simply, and avoid the automatic network detection of Windows XP every time it is switched on, so as to accelerate the startup! [method]: right-click on the "network neighborhood" - select properties, enter the window, right-click on the "local connection" - select properties here Double click the Internet protocol (TCP/IP), select use the following IP address, and then enter an IP address (such as: 192.168.0.1), The subnet mask defaults. (this does not cause any conflict with your Internet. This address is only used in the LAN) Second search will quickly find IP and quickly access the system. 3, disable temporarily unused equipment Acceleration principle: now the computer peripheral equipment price is quite cheap, many people bought the U disk, the mobile hard disk and so on the product, but many friends always It is after use that they forget to disconnect the USB devices from the host. As a result of the Windows XP system, the USB interface is automatically detected, so these If the device is connected to the host when it is turned on, it will cause the system to start slowly. I personally experienced a friend's computer connected to the mobile hard disk boot Unable to access the system only after disconnecting the line. Therefore, after you use the U disk, mobile hard disk, these USB devices, and When the connection with the host, but also prevent the boot, current shock and other accidents damage equipment (because many chassis manufacturers in order to reduce Cost, there is no necessary protection circuit at the pre - USB interface, even without the necessary grounding. Also, use a notebook friend if Temporarily unable to use infrared and wireless network cards, etc., should also be disabled in device manager. Because of these extensions, especially the network card, for The speed at which the system starts has a huge impact. After disabling, the process of accelerating the startup process is achieved by skipping the system startup test. Also note: because the system will automatically read the default drive, so the boot will be detected when the drive, if the CD-ROM is placed in the drive, Will automatically read, if it is a multimedia CD, then the time spent reading will be longer, the same time to extend the computer's start-up time. So suggest big Home usually use the CD, remember to take it out in time. 4. Close the theme and clear the table Lots of friends like beautiful themes or wallpapers, but beauty comes at a price. That's a lot of memory, and there's too much on the table The icons are the same. Because each time the system starts to display the desktop, you first need to check if the topic is enabled, and when you find it, it loads a lot The theme eats a lot of memory in this way. (in addition, many users do not perfect their own bodies, and many compatible problems will arise after using them System failure). At the same time, the system will also find and verify the validity of desktop shortcuts, so the more shortcuts, Verification time spent The longer. I suggest you usually try not to use the theme, set up a beautiful wallpaper at most. The desktop shortcut is then split into the door Other categories are placed in a special folder for easy management, and start shooting two birds at once! 5, turn off the unnecessary startup program Many software will automatically run some background programs after the system starts, such as: Winamp, office and so on These programs slow down the startup, and you should switch on "start" by "start - run", enter "msconfig" and "start" Close unnecessary startup items. Usually just keep the input method and firewall (according to personal settings). In addition, we recommend that you do not set the memory optimization software boot up. Because the boot up memory, not only the effect is very small, but also seriously affect Kai Dynamic speed, the correct approach should be in the operation of PhotoShop and other software that requires a lot of memory, the use of memory collation will be renamed, it seems effective Fruit. (actually, from the beginning of Win2000, the memory management of the operating system itself has been quite perfect, and it has developed to the memory management of winXP nowadays For scientific and effective use of memory, collation effects are limited 6, antivirus software is also troublesome Some antivirus software provides the system boot scan function, which will take a lot of time, in fact, if you have opened the antivirus software When monitoring function, and regularly check the system, then start the scanning system appears to be a bit redundant, or disable this function! These are no way, I think it should be your computer hard disk sector is broken. Do you usually have a dry sound when you use a computer? Often with dry sound, especially when running programs, there are dry sound, usually disk, there are bad sectors