9xII 的工程模式 (service menu)-航模-遥控飞机-遥控直升机-遥控模型

9xII 的工程模式 (service menu)-航模-遥控飞机-遥控直升机-遥控模型 9xII 的工程模式 (service menu)-航模-遥控飞机-遥控直升机-遥 控模型 9xII engineering model (service menu) 1, pull up the accelerator to hold (TH.HOLD) and switch the front itself (for the original factory mode 1 machine does not do this step) 2. Push the AILE D/R switch up 3, press and hold the ENT button on the panel to boot 4 rotate the roller until the Trim Step option is highlighted 5 press the scroll wheel into the Trim Step menu and rotate to ALIE 5.5, for the original factory mode 1 machine, pull the TRN switch (late change to mode2, also calculate mode1 machine) 6. Turn the AILE D/R switch down, press the wheel, push the AILE D/R switch, and press the roller again 7, repeat sixth steps, several times, when fifth (total) should be able to access Service Menu After many trials and discussions with foreign players, and finally successfully try out the 9xII menu service, enter the method and control of the stick mode is related, the above process is stick mode 2 method, for we buy most of the stick mode 1 control, to use TRN instead of TH.HOLD, the other the same (in the sixth step before pulling TRN can) Service menu applications 1. voltage alarm settings, for change of lithium TX, is suitable for 10.5V design 2. rocker and switch test, test all components move normally 3. rocker calibration and stroke, such as hair to the joystick neutral drift slightly, you can use rocker calibration function recalibration, after using a long time, potentiometer wear, there will be slight drift 4. (Advanced) throttle fine tuned to analog, in the United States and Europe's 9xII (XP9303) are 3+1 Trim mode, if you can get that throttle analog trim parts, you can change their own throttle simulation, the motherboard has a ready plug, as long as the service menu set up ANALOG TRIM Just fine 5. (Senior) short stroke throttle setting, limiting piece increase in the throttle, the throttle stroke is shortened, especially for Japan's TX by hand 6. turn off the stick mode selection function and set the default model type (HELI->AREO, etc) 7. (to rise) After setting up, there are three exits in the EXIT. Use the first item to quit and use other items to clear the model data and / or factory settings. Service menu applications 1. voltage alarm settings, for change of lithium TX, is suitable for 10.5V design 2. rocker and switch test, test all components move normally 3. rocker calibration and stroke, such as hair to the joystick neutral drift slightly, you can use rocker calibration function recalibration, after using a long time, potentiometer wear, there will be slight drift 4. (Advanced) throttle fine tuned to analog, in the United States and Europe's 9xII (XP9303) are 3+1 Trim mode, if you can get that throttle analog trim parts, you can change their own throttle simulation, the motherboard has a ready plug, as long as the service menu set up ANALOG TRIM Just fine 5. (Senior) short stroke throttle setting, limiting piece increase in the throttle, the throttle stroke is shortened, especially for Japan's TX by hand 6. turn off the stick mode selection function and set the default model type (HELI->AREO, etc) 7. (to rise) Service menu function list 一、退出退出 1。复位启动(未初始化)直接退出，不进行初始化 2。初始化模型数据和系统数据初始化模型数据和系统数据 三.初始化系统数据只仅初始化系统数据 2二项慎用 二、软件测试开关测试 测试所有开关动作是否正常，同时按下ENT和滚轮下压退出 三、硬。CON硬件配置(和跳线配置) 1。降低短行程油门 2。油门通道使用模拟拨杆式微调模拟技术 三.华泽宏大型(我还没查到) 4。初始化式初始化类型，默认是直升机(合力)，玩固定翼为主的可以改成肢端 5。弹出微调时显示跳出提示修剪 6。r.trm哔微调时发声(不过改变后没什么用，可能r.trm指的其它，默认是关闭) 7。TX的H / W的摇控器型号pcm9x_2和p9x_old，(可能同一固件应用于多种控) 8。美国模式可用户设置棒模式 9。ini.s.mode初始棒模式，不可设，由硬件跳线配置 10.th.dir油门方向可设置(硬跳线) 11.zpcm zpcm模式可用(硬跳线) 12.warn开机th.hold或f.mode不在正常时报警 13.imodule发射模块类型 更改1,2,3后需要摇杆重校准 四、杆螺母。摇杆中点位置 显示所有模拟量摇杆的中点位置，按功能最下按钮重记忆，按CLR清零 重置零点时把所有摇杆置在中点(包括油门) (由显示值可见9xii的摇杆是10bit采样的，- 511 - 511) 五、棒佐治亚州摇杆行程校准和电池设置 1。左半部是摇杆的上下行程数据，按CLR进行校准，摇动所有杆到最大最小值多次 2。右半部是电压测量值校准 三.锂备份锂电池电压(9xii不需要备份电池，使用EEPROM存储配置，永不丢失) 4。电池主电池电压校准，显示值和实际电池电压校正，调节数值使显示电池和测量电压一致 5。小蝙蝠设置报警电压，一般镍氢/镍镉电池设为9v(默认)，锂电池设为10.5v 6。对比面板对比度电压校准(9xii上无效，可能在带背光的9xii极限上有用) 六、初始化初始化数据 1。使用硬跳线来初始化模型数据的棒模式 2。初始化模型数据并重启设备 七、转移数据传输 把所有配置数据传输到另一台遥控设备，或接收另一台设备的数据 表键改变模式，CLR开始 八、内存监控内存数据查看 九、编辑内存数据直接修改(危险) 提示:不懂的项目请别随便乱动，可能导至摇控不工作，特别是重置工厂设置及RAM编辑器功能，错误的恢复工厂设置可能会丢失很多需要工厂校准的数据， 使用控不能正常工作， Must be returned to the factory for maintenance (re calibration) Attached: 9xII part of the main board jumper settings SJ0 SJ1 Activates ZPCM SJ2 SJ3 SJ4 SJ5 Deactiaves STICKMODE SJ6 SJ7 SJ8 SJ9 Activates STICKDIR SJ10 Deactivates TRANSFER SJ11 Activates IDELUP/TH.HOLD ALARM SJ12