为了正常的体验网站,请在浏览器设置里面开启Javascript功能!

交换机配置CLI-初级到高级

2019-05-18 22页 doc 53KB 63阅读

用户头像

is_737483

暂无简介

举报
交换机配置CLI-初级到高级1.在基于IOS的交换机上设置主机名/系统名: switch(config)# hostname hostname 在基于CLI的交换机上设置主机名/系统名: switch(enable) set system name name-string 2.在基于IOS的交换机上设置登录口令: switch(config)# enable password level 1 password 在基于CLI的交换机上设置登录口令: switch(enable) set password switch(enable) se...
交换机配置CLI-初级到高级
1.在基于IOS的交换机上设置主机名/系统名: switch(config)# hostname hostname 在基于CLI的交换机上设置主机名/系统名: switch(enable) set system name name-string 2.在基于IOS的交换机上设置登录口令: switch(config)# enable password level 1 password 在基于CLI的交换机上设置登录口令: switch(enable) set password switch(enable) set enalbepass 3.在基于IOS的交换机上设置远程访问: switch(config)# interface vlan 1 switch(config-if)# ip address ip-address netmask switch(config-if)# ip default-gateway ip-address 在基于CLI的交换机上设置远程访问: switch(enable) set interface sc0 ip-address netmask broadcast-address switch(enable) set interface sc0 vlan switch(enable) set ip route default gateway 4.在基于IOS的交换机上启用和浏览CDP信息: switch(config-if)# cdp enable switch(config-if)# no cdp enable 为了查看Cisco邻接设备的CDP通告信息: switch# show cdp interface [type modle/port] switch# show cdp neighbors [type module/port] [detail] 在基于CLI的交换机上启用和浏览CDP信息: switch(enable) set cdp {enable|disable} module/port 为了查看Cisco邻接设备的CDP通告信息: switch(enable) show cdp neighbors[module/port] [vlan|duplex|capabilities|detail] 5.基于IOS的交换机的端口描述: switch(config-if)# description description-string 基于CLI的交换机的端口描述: switch(enable)set port name module/number description-string 6.在基于IOS的交换机上设置端口速度: switch(config-if)# speed{10|100|auto} 在基于CLI的交换机上设置端口速度: switch(enable) set port speed moudle/number {10|100|auto} switch(enable) set port speed moudle/number {4|16|auto} 7.在基于IOS的交换机上设置以太网的链路模式: switch(config-if)# duplex {auto|full|half} 在基于CLI的交换机上设置以太网的链路模式: switch(enable) set port duplex module/number {full|half} 8.在基于IOS的交换机上配置静态VLAN: switch# vlan database switch(vlan)# vlan vlan-num name vla switch(vlan)# exit switch# configure teriminal switch(config)# interface interface module/number switch(config-if)# switchport mode access switch(config-if)# switchport access vlan vlan-num switch(config-if)# end 在基于CLI的交换机上配置静态VLAN: switch(enable) set vlan vlan-num [name name] switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于IOS的交换机上配置VLAN中继线: switch(config)# interface interface mod/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation {isl|dotlq} switch(config-if)# switchport trunk allowed vlan remove vlan-list switch(config-if)# switchport trunk allowed vlan add vlan-list 在基于CLI的交换机上配置VLAN中继线: switch(enable) set trunk module/port [on|off|desirable|auto|nonegotiate] Vlan-range [isl|dotlq|dotl0|lane|negotiate] 10.在基于IOS的交换机上配置VTP管理域: switch# vlan database switch(vlan)# vtp domain domain-name 在基于CLI的交换机上配置VTP管理域: switch(enable) set vtp [domain domain-name] 11.在基于IOS的交换机上配置VTP 模式: switch# vlan database switch(vlan)# vtp domain domain-name switch(vlan)# vtp {sever|cilent|transparent} switch(vlan)# vtp password password 在基于CLI的交换机上配置VTP 模式: switch(enable) set vtp [domain domain-name] [mode{ sever|cilent|transparent }][password password] 12. 在基于IOS的交换机上配置VTP版本: switch# vlan database switch(vlan)# vtp v2-mode 在基于CLI的交换机上配置VTP版本: switch(enable) set vtp v2 enable 13. 在基于IOS的交换机上启动VTP剪裁: switch# vlan database switch(vlan)# vtp pruning 在基于CL I 的交换机上启动VTP剪裁: switch(enable) set vtp pruning enable 14.在基于IOS的交换机上配置以太信道: switch(config-if)# port group group-number [distribution {source|destination}] 在基于CLI的交换机上配置以太信道: switch(enable) set port channel moudle/port-range mode{on|off|desirable|auto} 15.在基于IOS的交换机上调整根路径成本: switch(config-if)# spanning-tree [vlan vlan-list] cost cost 在基于CLI的交换机上调整根路径成本: switch(enable) set spantree portcost moudle/port cost switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list] 16.在基于IOS的交换机上调整端口ID: switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority 在基于CLI的交换机上调整端口ID: switch(enable) set spantree portpri {mldule/port}priority switch(enable) set spantree portvlanpri {module/port}priority [vlans] 17. 在基于IOS的交换机上修改STP时钟: switch(config)# spanning-tree [vlan vlan-list] hello-time seconds switch(config)# spanning-tree [vlan vlan-list] forward-time seconds ` switch(config)# spanning-tree [vlan vlan-list] max-age seconds 在基于CLI的交换机上修改STP时钟: switch(enable) set spantree hello interval[vlan] switch(enable) set spantree fwddelay delay [vlan] switch(enable) set spantree maxage agingtiame[vlan] 18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征: switch(config-if)#spanning-tree portfast 在基于CLI的交换机端口上启用或禁用Port Fast 特征: switch(enable) set spantree portfast {module/port}{enable|disable} 19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征: switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second] 在基于CLI的交换机端口上启用或禁用UplinkFast 特征: switch(enable) set spantree uplinkfast {enable|disable}[rate update-rate] [all-protocols off|on] 20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个 IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name 21. 为了从一条中继链路上删除VLAN,可使用下列命令: switch(enable) clear trunk module/port vlan-range 22. 用show vtp domain 显示管理域的VTP参数. 23. 用show vtp statistics显示管理域的VTP参数. 24. 在Catalyst交换机上定义TrBRF的命令如下: switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp {ieee|ibm}] 25. 在Catalyst交换机上定义TrCRF的命令如下: switch (enable) set vlan vlan-num [name name] type trcrf {ring hex-ring-num|decring decimal-ring-num} parent vlan-num 26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口: switch(enable) set vlan vlan-num mod-num/port-num 27. 命令show spantree显示一个交换机端口的STP状态. 28. 配置一个ELAN的LES和BUS,可以使用下列命令: ATM (config)# interface atm number.subint multioint ATM(config-subif)# lane serber-bus ethernet elan-name 29. 配置LECS: ATM(config)# lane database database-name ATM(lane-config-databade)# name elan1-name server-atm-address les1-nsap-address ATM(lane-config-databade)# name elan2-name server-atm-address les2-nsap-address ATM(lane-config-databade)# name … 30. 创建完数据库后,必须在主接口上启动LECS.命令如下: ATM(config)# interface atm number ATM(config-if)# lane config database database-name ATM(config-if)# lane config auto-config-atm-address 31. 将每个LEC配置到一个不同的ATM子接口上.命令如下: ATM(config)# interface atm number.subint multipoint ATM(config)# lane client ethernet vlan-num elan-num 32. 用show lane server 显示LES的状态. 33. 用show lane bus显示bus的状态. 34. 用show lane database显示LECS数据库可. 35. 用show lane client显示LEC的状态. 36. 用show module显示已安装的模块列表. 37. 用物理接口建立与VLAN的连接: router# configure terminal router(config)# interface media module/port router(config-if)# description description-string router(config-if)# ip address ip-addr subnet-mask router(config-if)# no shutdown 38. 用中继链路来建立与VLAN的连接: router(config)# interface module/port.subinterface router(config-ig)# encapsulation[isl|dotlq] vlan-number router(config-if)# ip address ip-address subnet-mask 39. 用LANE 来建立与VLAN的连接: router(config)# interface atm module/port router(config-if)# no ip address router(config-if)# atm pvc 1 0 5 qsaal router(config-if)# atm pvc 2 0 16 ilni router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-mask router(config-if)# lane client ethernet elan-num router(config-if)# interface atm module/port.subinterface multipoint router(config-if)# ip address ip-address subnet-name router(config-if)# lane client ethernet elan-name router(config-if)# … 40. 为了在路由处理器上进行动态路由配置,可以用下列IOS命令来进行: router(config)# ip routing router(config)# router ip-routing-protocol router(config-router)# network ip-network-number router(config-router)# network ip-network-number 41. 配置默认路由: switch(enable) set ip route default gateway 42. 为一个路由处理器分配VLANID,可在接口模式下使用下列命令: router(config)# interface interface number router(config-if)# mls rp vlan-id vlan-id-num 43. 在路由处理器启用MLSP: router(config)# mls rp ip 44. 为了把一个外置的路由处理器接口和交换机安置在同一个VTP域中: router(config)# interface interface number router(config-if)# mls rp vtp-domain domain-name 45. 查看指定的VTP域的信息: router# show mls rp vtp-domain vtp domain name 46. 要确定RSM或路由器上的管理接口,可以在接口模式下输入下列命令: router(config-if)#mls rp management-interface 47. 要检验MLS-RP的配置情况: router# show mls rp 48. 检验特定接口上的MLS配置: router# show mls rp interface interface number 49. 为了在MLS-SE上设置流掩码而又不想在任一个路由处理器接口上设置访问列表: set mls flow [destination|destination-source|full] 50. 为使MLS和输入访问列表可以兼容,可以在全局模式下使用下列命令: router(config)# mls rp ip input-acl 51. 当某个交换机的第3层交换失效时,可在交换机的特权模式下输入下列命令: switch(enable) set mls enable 52. 若想改变老化时间的值,可在特权模式下输入以下命令: switch(enable) set mls agingtime agingtime 53. 设置快速老化: switch(enable) set mls agingtime fast fastagingtime pkt_threshold 54. 确定那些MLS-RP和MLS-SE参与了MLS,可先显示交换机引用列表中的内容再确定: switch(enable) show mls include 55. 显示MLS高速缓存记录: switch(enable) show mls entry 56. 用命令show in arp显示ARP高速缓存区的内容。 57. 要把路由器配置为HSRP备份组的成员,可以在接口配置模式下使用下面的命令: router(config-if)# standby group-number ip ip-address 58. 为了使一个路由器重新恢复转发路由器的角色,在接口配置模式下: router(config-if)# standy group-number preempt 59. 访问时间和保持时间参数是可配置的: router(config-if)# standy group-number timers hellotime holdtime 60. 配置HSRP跟踪: router(config-if)# standy group-number track type-number interface-priority 61. 要显示HSRP路由器的状态: router# show standby type-number group brief 62. 用命令show ip igmp确定当选的查询器。 63. 启动IP组播路由选择: router(config)# ip muticast-routing 64. 启动接口上的PIM: dalllasr1>(config-if)# ip pim {dense-mode|sparse-mode|sparse-dense-mode} 65. 启动稀疏-稠密模式下的PIM: router# ip multicast-routing router# interface type number router# ip pim sparse-dense-mode 66. 核实PIM的配置: dallasr1># show ip pim interface[type number] [count] 67. 显示PIM邻居: dallasr1># show ip neighbor type number 68. 为了配置RP的地址,命令如下: dallasr1># ip pim rp-address ip-address [group-access-list-number][override] 69. 选择一个默认的RP: dallasr1># ip pim rp-address 通告RP和它所服务的组范围: dallasr1># ip pim send-rp-announce type number scope ttl group-list access-list-number 为管理范围组通告RP的地址: dallasr1># ip pim send-rp-announce ethernet0 scope 16 group-list1 dallasr1># access-list 1 permit 266.0.0.0 0.255.255.255 设定一个RP映像代理: dallasr1># ip pim send-rp-discovery scope ttl 核实组到RP的映像: dallasr1># show ip pim rp mapping dallasr1># show ip pim rp [group-name|group-address] [mapping] 70. 在路由器接口上用命令ip multicast ttl-threshold ttl-value设定TTL 阀值: dallasr1>(config-if)# ip multicast ttl-threshold ttl-value 71. 用show ip pim neighbor显示PIM邻居表。 72. 显示组播通信路由表中的各条记录: dallasr1>show ip mroute [group-name|group-address][scoure][summary][count][active kbps] 73. 要记录一个路由器接受和发送的全部IP组播包: dallasr1> #debug ip mpacket [detail] [access-list][group] 74. 要在CISCO路由器上配置CGMP: dallasr1>(config-if)# ip cgmp 75.配置一个组播路由器,使之加入某一个特定的组播组: dallasr1>(config-if)# ip igmp join-group group-address 76. 关闭 CGMP: dallasr1>(config-if)# no ip cgmp 77. 启动交换机上的CGMP: dallasr1>(enable) set cgmp enable 78. 核实Catalyst交换机上CGMP的配置情况: catalystla1>(enable) show config set prompt catalystla1> set interface sc0 192.168.1.1 255.255.255.0 set cgmp enable 79. CGMP离开的设置: Dallas_SW(enable) set cgmp leave 80. 在Cisco设备上修改控制端口密码: R1(config)# line console 0 R1(config-line)# login R1(config-line)# password Lisbon R1(config)# enable password Lilbao R1(config)# login local R1(config)# username student password cisco 81. 在Cisco设备上设置控制台及vty端口的会话超时: R1(config)# line console 0 R1(config-line)# exec-timeout 5 10 R1(config)# line vty 0 4 R1(config-line)# exec-timeout 5 2 82. 在Cisco设备上设定特权级: R1(config)# privilege configure level 3 username R1(config)# privilege configure level 3 copy run start R1(config)# privilege configure level 3 ping R1(config)# privilege configure level 3 show run R1(config)# enable secret level 3 cisco 83. 使用命令privilege 可定义在该特权级下使用的命令: router(config)# privilege mode level level command 84. 设定用户特权级: router(config)# enable secret level 3 dallas router(config)# enable secret san-fran router(config)# username student password cisco 85. 标志设置与显示: R1(config)# banner motd ‘unauthorized access will be prosecuted!’ 86. 设置vty访问: R1(config)# access-list 1 permit 192.168.2.5 R1(config)# line vty 0 4 R1(config)# access-class 1 in 87. 配置HTTP访问: Router3(config)# access-list 1 permit 192.168.10.7 Router3(config)# ip http sever Router3(config)# ip http access-class 1 Router3(config)# ip http authentication local Router3(config)# username student password cisco 88. 要启用HTTP访问,请键入以下命令: switch(config)# ip http sever 89. 在基于set命令的交换机上用setCL1启动和核实端口安全: switch(enable) set port security mod_num/port_num…enable mac address switch(enable) show port mod_num/port_num 在基于CiscoIOS命令的交换机上启动和核实端口安全: switch(config-if)# port secure [mac-mac-count maximum-MAC-count] switch# show mac-address-table security [type module/port] 90. 用命令access-list在通信量过滤表中创建一条记录: Router(config)# access-list access-list-number {permit|deny} source-address [source-address] 91. 用命令access-list在扩展通信量过滤表中创建一条记录: Router(config)# access-list access-list-number {permit|deny{protocol|protocol-keyword}}{source source-wildcard|any}{destination destination-wildcard|any}[protocol-specific options][log] 92. 对于带内路由更新,配置路由更新的最基本的命令格式是: R1(config-router)#distribute-list access-list-number|name in [type number] 93. 对于带外路由更新,配置路由更新的最基本的命令格式是: R1(config-router)#distribute-list access-list-number|name out [interface-name] routing-process| autonomous-system-number 94. set snmp命令选项: set snmp community {read-only|ready-write|read-write-all}[community_string] 95. set snmp trap 命令格式如下: set snmp trap {enable|disable} [all|moudle|classis|bridge|repeater| auth|vtp|ippermit|vmps|config|entity|stpx] set snmp trap rvcr_addr rcvr_community 96. 启用SNMP chassis 陷阱: Console>(enable) set snmp trap enable chassis 97. 启用所有SNMP chassis 陷阱: Console>(enable) set snmp trap enable …………以下由about于2002年12月6日增加…………98. 禁用SNMP chassis 陷阱: Console>(enable) set snmp trap disable chassis 99. 给SNMP陷阱接收表加一条记录: Console>(enable) set snmp trap 192.122.173.42 public 100. show snmp 输出结果。 101. 命令set snmp rmon enable 的输出结果。
/
本文档为【交换机配置CLI-初级到高级】,请使用软件OFFICE或WPS软件打开。作品中的文字与图均可以修改和编辑, 图片更改请在作品中右键图片并更换,文字修改请直接点击文字进行修改,也可以新增和删除文档中的内容。
[版权声明] 本站所有资料为用户分享产生,若发现您的权利被侵害,请联系客服邮件isharekefu@iask.cn,我们尽快处理。 本作品所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用。 网站提供的党政主题相关内容(国旗、国徽、党徽..)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。

历史搜索

    清空历史搜索