油性漆乳胶漆_不同油漆施工注意事项

油性漆乳胶漆_不同油漆施工注意事项 一、油性漆 1、施工环境的温度不能低于5摄氏度，湿度不宜大于百分之八十。 2、在实色漆工艺中如使用腻子或水灰，不能刮涂过厚，并且必须做到干透后彻底打磨，否则容易导致开裂脱落现象出现。 3、注意施工现场环境卫生和除尘处理，不良的施工环境和灰尘容易导致漆膜面有颗粒及其他异常漆病发生。 4、平面施工时严禁一次性厚涂，防止涂刷过厚导致出现发蒙现象。 5、层间打磨必须彻底，否则会导致附着不良的现象。 6、底漆禁止使用水磨，面漆使用水磨时必须彻底干透后再涂漆，防止发白和附着力不良。 7、控制基材含水率小于当地平衡含水率，针对含油或含水率教高的底材(如柚木板。松木板等需特别注意)，尽量将底材进行有效的封闭处理，以防止漆膜发白现象发生。(建议使用大宝专用封闭漆，如清风底漆)。 8、不能为追求快干速度，超量使用固化剂;在气温较底时，严禁使用一些不配套的快干固化剂，否则，会导致漆膜过脆，出现开裂、附着力不良、阴阳面以及失光等漆膜弊病。 二、乳胶漆 1、墙体温度小于或等于摄氏度，环境湿度大于及等于百分之八十五，严禁施工。 2、墙体基层含水率小于或等于百分之十五，ph值小于十。 3、墙体基层抹灰必须达到:墙体平整，用指甲扣不掉粉，手感光滑。 4、腻子最好是配套的腻子，自调腻子必须满足jg/t3049《建筑室内用腻子》的要求。严禁加入光油或醇酸清漆，以增加腻子粘结强度为目的材料在施工中使用，以防止乳胶漆施工后出现“黄”像(光油或醇酸清漆在腻子中呈黄相，在天气温度变化时，黄色色相即会在已涂装好的表面渗透出来)。 5、在秋冬季节施工，批刮腻子时一定要控制批刮厚度，以免影响腻子干燥而引起开裂问题;施工时不宜厚批，每遍腻子应该在前一遍腻子干燥以后才能批刮，一般居室批刮2-3遍即可。 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 6、在施工时，应该保证底漆封闭严密，如果基层松蔬，强度不够，宜封闭两遍底漆;每遍底漆必须保证干燥良好，用手指按压，不粘手，倾斜看墙面并有乳光，方可施工面漆。 7、刷涂、混涂有气喷涂及无气喷涂应严格按施工比，尽量薄涂、薄喷，以免由于温度太低时造成乳胶漆开裂、脱粉。 8、两遍面漆之间应保持充分的干燥时间，每遍间隔至少2小时(25摄氏度)以上，避免引起流挂。开裂。 9、若遇冬天有雾时，不可施工，要等待雾散日出，收干水气，方可施工。 中国十大油性漆品牌名称及LOGO在线投票 多乐士 (多乐士是阿克苏诺贝尔公司旗下世界驰名的建) 立邦漆 (立邦是世界著名的涂料制造商，成立于188) 华润漆 (广东华润涂料有限公司始建于1991年,公) 嘉宝莉 (广东嘉宝莉化工集团是国内最大的民营涂料生) 美涂士 (公司主要从事内外墙乳胶漆、装修漆、家具漆) 大宝漆 (大宝国际源自台湾，立足于中国大陆，是一家) 皇家钟意 (在全球各地设有生产基地和运营总部。其中美) 嘉丽士漆 (嘉丽士漆作为涂料行业的高端品牌，隶属于广) 三棵树 (三棵树连续四次入选由权威机构世界品牌实验) 紫荆花 (一直被香港房屋署列为认可的建筑物料，广泛) manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 环氧树脂地坪:是环氧树脂与固化剂固化后在地面形成表面明亮的表面、一般厚度有0.5毫米的薄涂型、2-5毫米的自流平型有溶剂型和无溶剂型。环氧树脂地坪引 目录 施工环境要求 特性 适用范围及性能特点 施工工艺 养护介绍 验收标准 环氧树脂地坪选择方法 施工环境要求 特性 适用范围及性能特点 施工工艺 养护介绍 验收标准 环氧树脂地坪选择方法 施工环境要求 1、施工的环境温度应控制在10?-35?; 2、基层含水率不能超过5% 3、空气湿度要小于75% 4、施工的环境温度应高于室外温度3?以上 环氧树脂地坪起泡原因 环氧树脂地坪起水泡多发生在一楼或地下室，有时二楼以上也时有发生，环氧树脂地坪起水泡一般在施工后不久就发现，有的上午铺贴的环氧树脂地坪下午就有水泡。水泡由小到大，不断发展，发展到一定程度后停止。气温越高，水泡就越容易发生，发展的速度也越快。水泡形状各异，其大小不一。有的水泡直径达1m以上，高度达20~50mm。 水泡的产生与施工地区没有明显的关系，同一地区有的严重，有的较轻，有的完好。同一小组操作，同一材料施工的环氧地面层，有的起水泡，有的完好，说明水泡是多种因素造成的。 起水泡的原因，是大家关心的一个问题，剖开水泡发现，泡内都含有水分或炎黄色液体，环氧地面层与基层脱离，粘在基层上的胶结料被拉成manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 峰窝状，见图1—1;按照“物理学”解释，在盛有液体的密闭容器内，液体蒸发，形成饱和状态的三条曲线的温度与压力关系。 在密闭的容器内，含有饱和水蒸汽的压力，是随着温度的升高而上升，当温度为20.C时，鼓包内的压力为0.01MPa;而当温度为70~80.C之间是直线上升到0.1MPa;很多地区在炎热的夏季地面的极端辐射热可达70.C左右，在这样的高温下，环氧胶结料已经软化粘力大大降低，因此就形同向轮胎内渐渐鼓气一样，使环氧地面层中鼓起了大包，将胶结料被拉成蜂窝状;其中没有起水泡的部分环氧层和地面部分沾不牢固，仔细观测接触部分，也会发现有无法固化的部分，原因是环氧有潮气不能固化;那么水分从何处来的呢,主要有以下几个水的来源: 1.基层、如水泥砂浆找平层，最大含水率达12%左右，基层的最大含水量大于找平层。 2.环氧中的其它配料内的脱水不尽。 3.环氧和基层施工时结合不好留下空隙和环氧本身的化学活性，没有完全固化或者是遇到潮湿气没有完全固化的残留物或气体。 4.基层的地下渗透的潮湿气体。 从以上四个方面来分析，基层的潮湿是主要的，绝对干燥的基层是没有的。含水率的大小也不能决定环氧树脂地坪是否会产生水泡，基层的部份水气和环氧残留物被包裹在环氧与基层内，形成大小不一的气泡，由于环氧层本身不透水气，水气不能排出，留下起泡的根苗。所以泡都产生在平面上，多在基层与环氧层之间;基层中的水分是很难避免的，这就是造成环氧地面层起水泡的重要因素。 特性 由特种环氧树脂添加适当溶剂，填料，表面活性剂和高级颜料等材料做为主剂，并采用改性脂肪胺做为固化剂，在常温条件下所形成的致密的三维交联涂层。具有: 1、 良好的耐磨性能， 2、 良好的抗碾压性能， 3、 优异的防渗透性能， 4、 中等条件下的防腐蚀性能， 5、 附着力良好，保证了涂层不龟裂、不脱落， 6、 外观平滑整洁，便于清洁维护， 7、 费用较低， 适用范围及性能特点 电器、电子、机械、食品、医药、化工、烟草、饮料、纺织、服装、家具、塑料、文体用品等制造工厂的车间水泥或水磨石地面。 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 性能特点: 环氧树脂地坪漆具有耐强酸碱、耐磨、耐压、耐冲击、防霉、防水、防尘、止滑以及防静电、电磁波等特性，颜色亮丽多样，清洁容易。它采用一次性涂覆工艺，不管有多大的面积，都不存在连接缝，而且还是一种无灰尘材料，具有附着力强，耐磨擦，硬度强等特点。 1、防尘、防潮、耐磨; 2、便于清洁、施工快捷、维护方便、造价低廉; 3、附着力强、柔韧性好、耐冲击; 4、厚度0.2-0.3? 施工工艺 素地处理:首先对原地面进行全面打磨，不平处需修复平整，然后清扫、 吸尘，潮湿处需先烘干。 底 层:用镘刀将调配好的纯树脂材料均匀地刮涂于原地面，与素地完全渗透 粘接，使其形成一层粘性较强的底层。 砂浆层:待底层固化后再将调配好的腻子层材料加石英砂全面均匀地用镘刀刮涂于底层之上，加强地坪的抗压、抗冲击性。(2mm将涂装两次) 中 层:待砂浆层固化后再进行全面打磨，将调配好的中涂材料用镘刀平镘于砂浆层之上，填补砂浆层上不平的小凹坑及针孔，使之均匀平整。 面 层:待中涂固化后，用打磨机全面研磨平整后清除干净，使中涂基面平整、光滑。将面涂材料调配搅拌后用镘刀均匀镘涂于中涂之上，形成一道防尘、防腐、耐磨、光洁、亮丽的自流平表层。 技术指标: 干燥时间 表干 ?4 实干 ?24 附着力(级) ?1 铅笔硬度 ?2H 耐冲击性 50通过 柔韧性 1?通过 耐磨性(750g/500R，失重g) ?0.03 耐水性 48小时无变化 耐30%硫酸 7天无变化 耐40%氢氧化钠 7天无变化 耐汽油 120# 7天无变化 耐润滑油 7天无变化 养护介绍 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 1. 建议行人穿软底鞋(若现场条件允许)，进入工业地坪区前要清理干净鞋底上的砂粒等硬质物，以减少锐利物体对地坪表面的划伤。 2. 搬运物品尽量做到轻举轻放，防止重物冲击地面，以免造成人为损坏。 3. 车间内的环氧地坪上行车要注意速度不可过快，以免争刹车行为造成剪切发热过高，从而使得环氧地坪漆瞬间软化(环氧地坪漆的软化温度在80?左右，因此其使用环境温度一般控制在50?以下)并在剪切力的作用下产生难以清洗的污痕。 4. 日常清洁可用地坪清洗机或湿抹布擦试，可选用中性清洁剂清洗，也可使用一般洗涤剂以较小浓度加入水中做成清洗液，然后使用地坪清洗机或棉布拖把洗净地坪表面的污渍，并用清水再洗一遍，擦干地面;注意地坪漆边缘部分不要较长时间有积水。 5. 不定期进行打蜡处理(一般每个月要打蜡一次)，建议使用专用地板蜡或乳化水性蜡;先使用地坪清洗机或棉布拖把将地坪清洗干净并拭干，然后打蜡处理。打蜡处理可以增加任何地坪材料的耐磨性及抗划伤性. 6. 避免使用重物或是工具敲击地面，也不可直接在环氧地面上拖移重物。 7. 避免重腐蚀性介质长时间浸泡地坪漆膜，如不慎重腐蚀性酸碱洒落，请务必及时清理干净酸碱介质。 验收标准 1、环境温度为25?时，施工后2-3天应达到实干，即硬度达到完成固化的80%左右; 2、表面不能出现发粘现象; 3、气泡:平涂型、砂浆型无气泡，自流平允许1个小气泡/10平方米; 4、流平性好，无镘刀痕，大面积接口处基本平整; 5、无浮色发花，颜色均匀一致，大面积接口处允许有极不明显的色差; 6、无粗杂质，但允许有空气中的浮尘掉落在造成的极小缺陷; 7、地坪表面应平整平滑，光泽度应达到要求(高光泽?90、有光?70、半光50,70)，平涂型为有光、水性为半光,无光; 8、桔皮、砂浆防滑面效果应很明显。 环氧树脂地坪几点关键: 1.素地质量 2.素地处理 3.地坪施工 4.清洁处理 1、基面处理 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 打磨、修补、清洁地面，使基面达到无空鼓、开裂、砂眼、坑洞、起壳和油污等。 2、环氧底涂涂装 环氧树脂渗透封闭底涂按比例把主剂与固化剂混合，充分搅拌均匀，在使用时间 内滚涂涂装，涂装做到要薄而匀，涂装后有光泽，无光泽之处，在适当时进行补 涂。 3、环氧砂浆中涂涂装 (1)批刮粗石英砂浆层:先将环氧树脂中涂主剂充分搅拌均匀，按比例把主剂与 固化剂混合，充分搅拌均匀，混合时将固化剂从主剂的桶中央倒入，避免材料混 合不均。搅拌后，再配比适量4,-6,的粗石英砂，采用刮刀刮涂工艺填补找平 基面。 (2)批刮细石英砂浆层:在混合好的环氧树脂中涂配比适量6,-8,的细石英砂， 同样采用批刀批刮，进一步增加中涂层的耐压及抗冲击性能。 根据地坪设计厚度多次批刮可重复(1)(2)道工序，待砂浆中涂层固化后打磨、 吸尘干净。 4、环氧腻子中涂涂装 先将环氧树脂中涂主剂充分搅拌均匀，按比例把主剂与固化剂混合，充分搅拌均 匀，混合时将固化剂从主剂的桶中央倒入，避免材料混合不均。搅拌后，再配比 适量石英粉批刮填补、封闭砂浆层的砂眼、毛细孔平滑基面，使环氧面涂施工达 到美观、平整。 5、环氧自流平面涂涂装 将无溶剂环氧树脂自流平面涂主剂充分搅拌均匀，按比例把主剂与固化剂混合， 充分搅拌均匀，混合时将固化剂从主剂的桶中央倒入，避免材料混合不均。充分 搅拌均匀，倒于地面上，用专用带齿镘刀镘刮涂装，先处理墙脚及犄角，再整体 镘涂一道。涂装时发现砂粒可杂物及时拣出，以免影响表观效果。 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 6、面漆保养 面涂完成将有关施工材料、工具搬离现场，严密封闭保护完成饰面，至少24 小时后才可允许人进入行走，不可带进泥沙。 环氧树脂地坪种类 环氧树脂地坪大致可以分为:薄涂型环氧地坪、环氧砂浆地坪、环氧自流平地坪、环氧抗静电地坪、车库坡道专用地坪，还有其他个性化产品:环氧彩砂地坪、水晶彩石地坪、裸粒彩石地坪、环氧大理石地坪、耐高温防火地坪、体育专用地坪等。 环氧树脂地坪选择方法 为了帮助使用地坪装饰保护涂料的顾客正确地选择地坪的种类和有效控制建设成本，建议顾客最好从以下几个因素入手: 一、机械性能要求 主要以下三个方面: 1. 耐磨性:地坪在使用时会有哪些车辆行走; 2. 耐压性:地坪在使用时会承受多大荷载; 3. 耐冲击性:冲击力是否会引起地坪面剥离; 二、化学性能要求 主要考虑以下两个方面: 1. 耐酸碱性:使用时腐蚀性化学物质的种类及浓度。 2. 耐溶剂性:使用时溶剂类型及接触时间。 三、楼层位置状况 根据地坪是在地下楼层还是地面楼层的位置，确定是否需要防潮处理或选择特殊防潮地坪, 四、基面状况 1. 基层强度:一般要求抗压强度?20Mpa 2. 平整度:是否需要用环氧砂浆修补, 3.地面施工前一般需要用自流平处理 五、美观要求 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget 1. 颜色要求:是否需要颜色划分区域, 2. 亮度要求:是选择哑光还是亮光, 3. 平整度要求:是否对地坪的平整度有要求, 六、安全性要求 如果地坪处在油渍环境或坡道处，则需要选择防滑地坪;如果在加油 站，油库等特殊场所需要选择防静电、防爆的。 manufacturers of technical documents on the quality requirements applicable to this project. Construction quality inspection and evaluation standards issued by the national power company of the electric power construction standard for quality inspection and assessment of the 11 articles assessment inspection standards as well as other relevant regulations issued by the Ministry of electric power, the State power company executive. Does not verify in the specification within the evaluation criteria, implementation design, manufacturer or ... Or issue a new national standards and regulations, bidders shall comply with new norms and standards. If there are conflicts or is inconsistent, whichever is the higher standards. 3.3 3.3.1 project of responsibility, authority and communication organization and project managers, at all levels of responsibility and authority see section II of chapter III of the present tender site management organization and part of workforce planning. 3.3.2 according ISO 9001, GB/T 50430 and company quality distribution of the quality manual, combining the departments of projects, project quality function distribution allocation table on the following page of the project's quality functions shown below. 3.3.3 project with each Department interface, interface between the internal departments of the project by project managers at all levels and the quality regulations of the responsibilities and authorities of the Department. Customer requirements and hope: project management; Quality planning, management program: the project's quality control Department; Site design: Project Engineering Department; Contract: the contract budget