一台主机两个显示器用法安装方法

一台主机两个显示器用法安装方法 安装方法: 一、连接好硬件 1.将显示器接到显卡的第二个VGA端口，插好USB键盘和USB鼠标。进入系统以后系统会检测到多个监视器、鼠标和键盘。晃动USB鼠标，确保光标能够移动。按下键盘的大小写锁定键，两个键盘的指示灯都应该点亮。如果没有检测到鼠标键盘，请确认连接正确。 2.启动系统多显示功能。打开“显示属性”中的“设置”选项卡，这时应该看到两个显示器连接。选择第二个显示器，选择“将Windows桌面扩展到该监视器上”。确认后第二显示器就能显示桌面了，并且鼠标光标能够在两个显示器之间移动。 medium above the surface of the pipe and heat, and their spacing is greater than 150mm. Tubing when laid horizontally, should according to different requirement of the 1:10~1:100 slope, tilt should be guaranteed to exclude gas or condensate. 5.1.7.5 angle and u-tube for pressure pipe cards, isolation with a rubber plate, bracket horizontal laying spacing for the 1~1.5M, vertical laying spacing for the 1.5~2m. 5.1.7.6 after you finish laying tubing, should be blowing and pressure testing, air tightness test. 5.1.8 gas pipe laying 5.1.8.1 gas supply system using pipes, valves, fittings, cleaning should be carried out prior to installation, there should be no oil, water, corrosion and dirt. 5.1.8.2 air tubes after cutting, remove end of iron, smooth polished pipe end. Threaded connections, not seal welded, sealed with Teflon tape. Terminal Connection pipes should have a sufficient number of allowances, reduce the effects of vibration and stress. 5.1.8.3 air tube should be used to pipe rack, suitable structures, non-removable device support, terminal be fixed firmly in the 0.9m, bracket 2m. Pipe is not supported on device or process piping: might move or motion of an object, such as heat exchangers, control valves; diameter 3 "pipe, insulation pipe liquid pipe, 1000C, high temperatures of over. 5.1.8.4 dismantling the pipeline in place, should provide a Union. Laid in each pipe, should be installed at least and the possible number of fittings. Perpendicular to the long end of the gas in the pipeline should have a drain valve. 5.1.9 field instrument installation 5.1.9.1 General requirements 5.1.9.1.1 instrument installation according to the design drawings to carefully check their equipment number, type, size and material. 5.1.9.1.2 instrument shall be mounted without mechanical vibration and away from magnetic fields and high 提示:如果主机为台式机，且使用了双显卡，还需要首先单独安装每个显卡的驱动程序。 注意:如果显示器、键盘、鼠标其中一个没有连接正确，请连接正确以后再进行下列步骤，否则会导致Windows XP系统出错。 二、配置用户和软件 1.打开“控制面板”的“用户账户”，添加一个用户并设置权限。在这里，俺设置了两个计算机管理员账户“书房”和“客厅”。 2.安装完软件后，(文章结尾有软件安装说明或参考压缩文件里的Readme.txt)必须重启以便继续配置系统。重启后出现BeTwin的设置向导。确定后按各个屏幕提示配置鼠标键盘。配置完后重启系统。 三、第一次登录 1.如果一切顺利的话，重启后会看到两个显示器上都显示了登录界面。主机用“书房”登录，子机用“客厅”登录。你会发现登录后与两个单独的 Windows XP环境并没有什么区别，两个键盘鼠标能够独立操作了。 medium above the surface of the pipe and heat, and their spacing is greater than 150mm. Tubing when laid horizontally, should according to different requirement of the 1:10~1:100 slope, tilt should be guaranteed to exclude gas or condensate. 5.1.7.5 angle and u-tube for pressure pipe cards, isolation with a rubber plate, bracket horizontal laying spacing for the 1~1.5M, vertical laying spacing for the 1.5~2m. 5.1.7.6 after you finish laying tubing, should be blowing and pressure testing, air tightness test. 5.1.8 gas pipe laying 5.1.8.1 gas supply system using pipes, valves, fittings, cleaning should be carried out prior to installation, there should be no oil, water, corrosion and dirt. 5.1.8.2 air tubes after cutting, remove end of iron, smooth polished pipe end. Threaded connections, not seal welded, sealed with Teflon tape. Terminal Connection pipes should have a sufficient number of allowances, reduce the effects of vibration and stress. 5.1.8.3 air tube should be used to pipe rack, suitable structures, non-removable device support, terminal be fixed firmly in the 0.9m, bracket 2m. Pipe is not supported on device or process piping: might move or motion of an object, such as heat exchangers, control valves; diameter 3 "pipe, insulation pipe liquid pipe, 1000C, high temperatures of over. 5.1.8.4 dismantling the pipeline in place, should provide a Union. Laid in each pipe, should be installed at least and the possible number of fittings. Perpendicular to the long end of the gas in the pipeline should have a drain valve. 5.1.9 field instrument installation 5.1.9.1 General requirements 5.1.9.1.1 instrument installation according to the design drawings to carefully check their equipment number, type, size and material. 5.1.9.1.2 instrument shall be mounted without mechanical vibration and away from magnetic fields and high 2.打开桌面上的BeTwin控制台，可以看到两个用户已经同时登录了。选择“用户”下的“统计信息”可以看到当前系统状态。如果可用内存太少，请添加内存，否则一拖二的运行速度会变得相当慢。 3.如果需要加入更多的电脑或者更改硬件属性，可以点击工作站配置。在弹出的窗口中可以看到当前分配给各个子系统的硬件状态，并可以修改配置。 如果需要终止工作站或者增添、删除硬件，选择“选项”中的“设置配置”，选择“禁用medium above the surface of the pipe and heat, and their spacing is greater than 150mm. Tubing when laid horizontally, should according to different requirement of the 1:10~1:100 slope, tilt should be guaranteed to exclude gas or condensate. 5.1.7.5 angle and u-tube for pressure pipe cards, isolation with a rubber plate, bracket horizontal laying spacing for the 1~1.5M, vertical laying spacing for the 1.5~2m. 5.1.7.6 after you finish laying tubing, should be blowing and pressure testing, air tightness test. 5.1.8 gas pipe laying 5.1.8.1 gas supply system using pipes, valves, fittings, cleaning should be carried out prior to installation, there should be no oil, water, corrosion and dirt. 5.1.8.2 air tubes after cutting, remove end of iron, smooth polished pipe end. Threaded connections, not seal welded, sealed with Teflon tape. Terminal Connection pipes should have a sufficient number of allowances, reduce the effects of vibration and stress. 5.1.8.3 air tube should be used to pipe rack, suitable structures, non-removable device support, terminal be fixed firmly in the 0.9m, bracket 2m. Pipe is not supported on device or process piping: might move or motion of an object, such as heat exchangers, control valves; diameter 3 "pipe, insulation pipe liquid pipe, 1000C, high temperatures of over. 5.1.8.4 dismantling the pipeline in place, should provide a Union. Laid in each pipe, should be installed at least and the possible number of fittings. Perpendicular to the long end of the gas in the pipeline should have a drain valve. 5.1.9 field instrument installation 5.1.9.1 General requirements 5.1.9.1.1 instrument installation according to the design drawings to carefully check their equipment number, type, size and material. 5.1.9.1.2 instrument shall be mounted without mechanical vibration and away from magnetic fields and high BeTwin”并重启系统即可。 四、注意事项 1.由于考虑到兼容性的问，BeTwin会将显卡的加速功能降低。为了取得最好的效果，在“显示属性?高级?疑难解答”中将硬件加速级别调到最高，这样主机、子机就可以玩3D游戏了。 2.最好不要同时运行占用系统资源太大的程序以免影响使用。尽量使用NTFS分区，为每个用户设置权限，确保每个用户隐私安全。 3.有些3D程序会导致两个显示器输出相同，此时第二个用户不能操作，只有重启才能解决问题。在试用中发现Windows XP的3D屏保会出现这个问题。 五、总结 在试用后发现，为了能够更好地使用该解决软件，推荐主机配置如下: CPU:P4 2.2GHz以上或同档次AMD CPU。具有超线程的CPU更好,如果是双核或是四核的就更理想啦～～～ 内存:256MB+工作站数目×128MB 显卡:支持双头输出的显卡或者再配一个PCI显卡。推荐GeForce 4以上带32MB以上显存的显卡。 从整个安装过程来看，BeTwin的安装过程相对傻瓜化，新手也很容易上手。从系统运行效果来看，两个用户的操作几乎不会互相影响。如果主机性能够强劲，还可以同时运行两个3D游戏，对于常见应用都能轻松对付。 网络方面只需要主机能够上网，子机无须配置就可以使用，但由于使用的同一个IP地址，局域网的应用就谈不上了。 总体来讲，BeTwin用于家庭一拖二已经基本够用，而且能极大地节约成本。 BeTwin安装说明:解压缩文件后运先行Buddy 2.00.419setup.exe安装，安medium above the surface of the pipe and heat, and their spacing is greater than 150mm. Tubing when laid horizontally, should according to different requirement of the 1:10~1:100 slope, tilt should be guaranteed to exclude gas or condensate. 5.1.7.5 angle and u-tube for pressure pipe cards, isolation with a rubber plate, bracket horizontal laying spacing for the 1~1.5M, vertical laying spacing for the 1.5~2m. 5.1.7.6 after you finish laying tubing, should be blowing and pressure testing, air tightness test. 5.1.8 gas pipe laying 5.1.8.1 gas supply system using pipes, valves, fittings, cleaning should be carried out prior to installation, there should be no oil, water, corrosion and dirt. 5.1.8.2 air tubes after cutting, remove end of iron, smooth polished pipe end. Threaded connections, not seal welded, sealed with Teflon tape. Terminal Connection pipes should have a sufficient number of allowances, reduce the effects of vibration and stress. 5.1.8.3 air tube should be used to pipe rack, suitable structures, non-removable device support, terminal be fixed firmly in the 0.9m, bracket 2m. Pipe is not supported on device or process piping: might move or motion of an object, such as heat exchangers, control valves; diameter 3 "pipe, insulation pipe liquid pipe, 1000C, high temperatures of over. 5.1.8.4 dismantling the pipeline in place, should provide a Union. Laid in each pipe, should be installed at least and the possible number of fittings. Perpendicular to the long end of the gas in the pipeline should have a drain valve. 5.1.9 field instrument installation 5.1.9.1 General requirements 5.1.9.1.1 instrument installation according to the design drawings to carefully check their equipment number, type, size and material. 5.1.9.1.2 instrument shall be mounted without mechanical vibration and away from magnetic fields and high 装完毕后重新启动即可。 【软件名称】:BeTwin 【软件大小】:14 MB 【软件语言】:简体中文 【分类目录】:应用软件 【运行环境】:Windows XP/2000/NT/Vista 【授权方式】:试用版 【官方网站】: medium above the surface of the pipe and heat, and their spacing is greater than 150mm. Tubing when laid horizontally, should according to different requirement of the 1:10~1:100 slope, tilt should be guaranteed to exclude gas or condensate. 5.1.7.5 angle and u-tube for pressure pipe cards, isolation with a rubber plate, bracket horizontal laying spacing for the 1~1.5M, vertical laying spacing for the 1.5~2m. 5.1.7.6 after you finish laying tubing, should be blowing and pressure testing, air tightness test. 5.1.8 gas pipe laying 5.1.8.1 gas supply system using pipes, valves, fittings, cleaning should be carried out prior to installation, there should be no oil, water, corrosion and dirt. 5.1.8.2 air tubes after cutting, remove end of iron, smooth polished pipe end. Threaded connections, not seal welded, sealed with Teflon tape. Terminal Connection pipes should have a sufficient number of allowances, reduce the effects of vibration and stress. 5.1.8.3 air tube should be used to pipe rack, suitable structures, non-removable device support, terminal be fixed firmly in the 0.9m, bracket 2m. Pipe is not supported on device or process piping: might move or motion of an object, such as heat exchangers, control valves; diameter 3 "pipe, insulation pipe liquid pipe, 1000C, high temperatures of over. 5.1.8.4 dismantling the pipeline in place, should provide a Union. Laid in each pipe, should be installed at least and the possible number of fittings. Perpendicular to the long end of the gas in the pipeline should have a drain valve. 5.1.9 field instrument installation 5.1.9.1 General requirements 5.1.9.1.1 instrument installation according to the design drawings to carefully check their equipment number, type, size and material. 5.1.9.1.2 instrument shall be mounted without mechanical vibration and away from magnetic fields and high